Battery Positive Cable Replacement LAT

Important: 

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
3. Disconnect the engine wiring harness electrical connector (1) from the starter.



4. Remove the positive battery cable to starter motor nut (1).
5. Remove the positive battery cable lead (2) from the starter motor.



6. Remove the positive battery cable clip (2) from the oil level indicator tube bracket (1).
7. Lower the vehicle.



8. Disengage the two side retaining tabs on the positive battery cable cover (1), and open the cover.
9. Remove the battery positive cable extension cable nut (2).
10. Remove the battery positive cable extension cable lead (3) from the positive battery cable.



11. Remove the underhood bussed electrical connector (UBEC) cover (1).



12. Loosen the integral bolt (5) on the positive battery cable lead (4) and remove the lead from the UBEC.
13. Loosen the positive battery cable nut (2).
14. Remove the positive battery cable (3) from the battery.



15. Cut, remove and discard the tape (1) securing the positive cable to the negative cable.
16. Separate the positive battery cable (4) from the negative battery cable (3).

Important: Note the routing of the positive battery cable assembly prior to removing.

17. Remove the positive battery cable assembly.

1. Place the NEW positive battery cable (4) next to the negative battery cable (3).
2. Install NEW tape (1) securing the positive cable to the negative cable.
3. Place the positive battery cable assembly into position in the vehicle as noted during removal.



4. Install the positive battery cable (3) to the battery.

Notice: Refer to Fastener Notice in the Preface section.

5. Tighten the positive battery cable nut (2).

Tighten
Tighten the nut to 10 N·m (89 lb in).

6. Position positive battery cable lead (4) to the UBEC and tighten the integral bolt (5).

Tighten
Tighten the bolt to 5 N·m (44 lb in).




7. Install the UBEC cover (1).



8. Install the battery positive cable extension cable lead (3) to the positive battery cable.
9. Install the battery positive cable extension cable nut (2).

Tighten
Tighten the nut to 10 N·m (89 lb in).

10. Close the positive battery cable cover (1).



11. Install the positive battery cable clip (2) to the oil level indicator tube bracket (1).



12. Raise and suitably support the vehicle.
13. Install the positive battery cable lead (2) to the starter motor.
14. Install the positive battery cable to starter motor nut (1).

Tighten
Tighten the nut to 10 N·m (89 lb in).




15. Connect the engine wiring harness electrical connector (1) to the starter.
16. Lower the vehicle.
17. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Positive Cable Replacement LZ4

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
2. Loosen the positive battery cable bolt and remove the positive battery cable from the battery.
3. Loosen the positive battery cable bolt at the junction block and remove the cable from the junction block.
4. Remove the positive battery cable clip from the battery tray.
5. Remove the tape holding the negative battery cable to the positive battery cable.



6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
7. Remove the positive battery cable nut (3) from the starter solenoid.
8. Remove the positive battery cable (1) from the starter solenoid.
9. Lower the vehicle.
10. Remove the positive battery cable.

1. Install the positive battery cable.
2. Raise and the vehicle.
3. Install the positive battery cable (1) to the starter solenoid.

Notice: Refer to Fastener Notice in the Preface section.

4. Install the positive battery cable nut (3) to the starter solenoid.

Tighten
Tighten the nut to 10 N·m (89 lb in).

5. Lower the vehicle.
6. Install the positive battery cable to the junction block and tighten the positive battery cable bolt.

Tighten
Tighten the bolt to 10 N·m (89 lb in).

7. Install the positive battery cable clip (4) to the battery tray.
8. Install tape in order to secure the negative battery cable to the positive battery cable.
9. Position the positive battery cable to the battery.
10. Tighten the positive battery cable bolt.

Tighten
Tighten the bolt to 17 N·m (13 lb ft).

11. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive Cable Replacement LY7

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
2. Disconnect the positive battery cable from the battery.
3. Loosen the positive battery cable bolt at the junction block and remove the cable from the junction block.
4. Remove the positive battery cable clip from the battery tray.
5. Remove the tape holding the negative battery cable to the positive battery cable.



6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
7. Remove the positive battery cable nut from the starter solenoid.
8. Remove the positive battery cable from the starter solenoid.
9. Lower the vehicle.
10. Remove the positive battery cable from the vehicle.

1. Route the positive cable to the starter and the battery.
2. Raise the vehicle.
3. Install the positive cable to the starter solenoid.

Notice: Refer to Fastener Notice in the Preface section.

4. Install the positive cable nut to the starter solenoid stud.

Tighten
Tighten the nut to 13 N·m (115 lb in).

5. Lower the vehicle.
6. Install the positive cable to the junction block and tighten the positive cable bolt.

Tighten
Tighten the bolt to 10 N·m (89 lb in).

7. Install the positive cable clip (4) to the battery tray.
8. Install tape to secure the negative battery cable to the positive battery cable.
9. Install the positive cable to the positive terminal of the battery.
10. Tighten the positive cable bolt).

Tighten
Tighten the bolt to 17 N·m (13 lb ft).

11. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.