Rear Compartment Lid Emblem/Nameplate Replacement. Saturn AURA 2009

For 1990-2009 cars only

Makes 🢒 Saturn 🢒 2009 🢒 AURA 🢒 Body Hardware and Trim 🢒 Exterior Trim 🢒 Rear Compartment Lid Emblem/Nameplate Replacement

Rear Compartment Lid Emblem/Nameplate Replacement Saturn

Callout

Component Name

Rear Compartment Lid Name Plate Assembly

Tip

•	When removing protective liners from adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.

•	Use a J 25070 or equivalent to remove old nameplate. Clean all adhesive from rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing new nameplate.

Rear Compartment Lid Emblem/Nameplate Replacement AURA XE

Callout	Component Name
1	Rear Compartment Lid Applique Emblem (AURA) Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made. Special Tools J-25070 Heat Gun
2	Rear Compartment Lid Applique Emblem (XE) Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Callout

Component Name

Rear Compartment Lid Applique Emblem (AURA)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Special Tools

J-25070 Heat Gun

Rear Compartment Lid Applique Emblem (XE)

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Rear Compartment Lid Emblem/Nameplate Replacement AURA XR 3.6

Callout	Component Name
1	Rear Compartment Lid Applique Emblem (3.6) Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made. Special Tools J-25070 Heat Gun
2	Rear Compartment Lid Applique Emblem (XR) Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Callout

Component Name

Rear Compartment Lid Applique Emblem (3.6)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Special Tools

J-25070 Heat Gun

Rear Compartment Lid Applique Emblem (XR)

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Rear Compartment Lid Emblem/Nameplate Replacement AURA XE 3.5

Callout	Component Name
1	Rear Compartment Lid Applique Emblem (3.5) Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made. Special Tools J-25070 Heat Gun

Callout

Component Name

Rear Compartment Lid Applique Emblem (3.5)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Special Tools

J-25070 Heat Gun

Rear Compartment Lid Emblem/Nameplate Replacement AURA FFU

Callout	Component Name
1	Rear Compartment Lid Emblem Assembly (FlexFuel) Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made. Special Tools J-25070 Heat Gun

Callout

Component Name

Rear Compartment Lid Emblem Assembly (FlexFuel)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Special Tools

J-25070 Heat Gun

Rear Compartment Lid Emblem/Nameplate Replacement AURA Hybrid

Callout	Component Name
1	Emblem/Nameplate Assembly (AURA) Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J-25070 gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made. Special Tools J-25070 Heat Gun
2	Emblem/Nameplate Assembly (HYBRID) Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J-25070 gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the rear compartment lid. Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Callout

Component Name

Emblem/Nameplate Assembly (AURA)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J-25070 gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.

Special Tools

J-25070 Heat Gun

Emblem/Nameplate Assembly (HYBRID)

Procedure

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J-25070 gun or equivalent to remove the old emblem/nameplate. Clean all adhesive from rear compartment lid and wipe the surface dry with a clean lint-free towel prior to installing the new emblem/nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the rear compartment lid.
Wet out the emblem/nameplate and ensure full adhesion of the emblem/nameplate to the rear compartment lid is made.