Special Tools

1. Remove the rear toothed belt cover. Refer to Timing Belt Rear Cover Replacement.
2. Remove MK-6628 .

Counterhold at hexagon of camshafts.

3. Remove the 1st camshaft bearing support.

•	Remove the 4 bolts.

Note removal sequence 1-4.

•	Release the bearing support by striking it gently with a plastic hammer.





Note: Mark camshaft bearing caps before removal.

4. Remove the exhaust camshaft.

•	Detach the camshaft bearing caps 2-5 working from outside to inside in a spiral in steps of 1/2 up to 1 turn.

•	Remove the camshaft bearing cover from the cylinder head and take out the camshaft.

Note: Mark camshaft bearing caps before removal.

5. Remove the intake camshaft.

•	Detach the camshaft bearing caps 2-5 working from outside to inside in a spiral in steps of 1/2 up to 1 turn.

•	Remove the camshaft bearing cover from the cylinder head and take out the camshaft.

6. Detach the seal rings from the camshafts.

Caution: Refer to Fastener Caution in the Preface section.




1. Install the exhaust camshaft.

•	Coat with MoS 2 lubricating paste.

Note: Note the identification marking on the camshaft bearing cover.

•	Insert the camshaft.

•	Install the camshaft bearing cover.

•	Tighten the camshaft bearing caps 2-5 in a spiral from the inside to the outside.

Tighten
Tighten the camshaft bearing caps to 8 N·m (70 lb in).

Note: If none of the camshafts were replaced, continue at step 3 of the Installation Procedure.

2. Install the intake camshaft.

•	Coat with MoS 2 lubricating paste.

Note: Note the identification marking on the camshaft bearing cover.

•	Insert the camshaft.

•	Install the camshaft bearing cover.

•	Tighten the camshaft bearing caps 2-5 in a spiral from the inside to the outside.

Tighten
Tighten the camshaft bearing caps to 8 N·m (70 lb in).

3. Install the 1st camshaft bearing support.

Tighten
Tighten the 4 bolts to 8 N·m (70 lb in).

Note: It is not necessary to replace the sealing sleeve and bolt when inspecting the valve lash.

4. Install the intake camshaft adjuster.

Install the bolt.

Note: It is not necessary to replace the sealing sleeve and bolt when inspecting the valve lash.

5. Attach the exhaust camshaft adjuster.

Install the bolt.

6. Tighten the intake camshaft adjuster.

Tighten
Tighten the intake camshaft adjuster to 65 N·m (48 lb ft).

7. Counterhold at camshaft hexagon.
8. Tighten the exhaust camshaft adjuster.

Tighten
Tighten the exhaust camshaft adjuster to 65 N·m (48 lb ft).

9. Counterhold at camshaft hexagon.
10. When replacing the intake camshaft, inspect the valve lash of the intake valves.
11. Inspect the 2 valve lash, intake valve cylinder 1.

•	Turn the intake camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 1 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

12. Inspect the 2 valve lash, intake valve cylinder 3.

•	Turn the intake camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 3 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

13. Inspect the 2 valve lash, intake valve cylinder 4.

•	Turn the intake camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 4 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

14. Inspect the 2 valve lash, intake valve cylinder 2.

•	Turn the intake camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 2 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

15. When replacing the exhaust camshaft, inspect the valve lash of the exhaust valves.
16. Inspect the 2 valve lash, exhaust valve cylinder 4.

•	Turn the exhaust camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 4 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

17. Inspect the 2 valve lash, exhaust valve cylinder 2.

•	Turn the exhaust camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 2 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

18. Inspect the 2 valve lash, exhaust valve cylinder 1.

•	Turn the exhaust camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 1 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

19. Inspect the 2 valve lash, exhaust valve cylinder 3.

•	Turn the exhaust camshaft in the direction of engine rotation by the bolt of the drive gear until the cams of cylinder 3 are in the test position.

•	Inspect the valve lash with KM-6361 .

Mark down result.

20. Detach the exhaust camshaft adjuster.

•	Remove the bolt.

•	Counterhold at the exhaust camshaft hexagon.

21. Detach the intake camshaft adjuster.

•	Remove the bolt.

•	Counterhold at hexagon of the intake camshaft.

22. Remove the 1st camshaft bearing support.

Remove the 4 bolts.

Note: Mark the camshaft bearing caps before removing them.

23. Remove the intake camshaft.

•	Detach the camshaft bearing caps 2-5 working from outside to inside in a spiral in steps of 1/2 up to 1 turn.

•	Remove the camshaft bearing cover from the cylinder head and take out the camshaft.

Note: Mark the camshaft bearing caps before removing them.

24. Remove the exhaust camshaft.

•	Detach the camshaft bearing caps 2-5 working from outside to inside in a spiral in steps of 1/2 up to 1 turn.

•	Remove the camshaft bearing cover from the cylinder head and take out the camshaft.

25. Remove the 16 cup tappets with KM-845 (1).



26. Determine cup tappet size.

Example of determining the size of the cup tappet:

•	Measurement of the cup tappet installed 3.12 mm (identification number 12)

•	Measured value between cams and cup tappets + 0.31 mm = 3.43 mm

•	Required value, valve lash - 0.25 mm

Note: The identification number (arrow) is on the inside of the cup tappet.

•	Measurement of the new cup tappet = 3.18 mm (identification number 18)

•	Now use a cup tappet with this dimension or one that is nearest to it.

1. Insert the 16 cup tappets with KM-845 .

Lightly coat sliding surfaces with oil.

2. Install the intake camshaft.

•	Coat with MoS 2 lubricating paste.

Note: Note the identification marking on the camshaft bearing cover.

•	Insert the camshaft.

•	Install the camshaft bearing cover.

•	Tighten the camshaft bearing caps 2-5 in a spiral from the inside to the outside.

Tighten
Tighten the camshaft bearing caps to 8 N·m (70 lb in).




3. Install the exhaust camshaft.

•	Coat with MoS 2 lubricating paste.

Note: Note the identification marking on the camshaft bearing cover.

•	Insert the camshaft.

•	Install the camshaft bearing cover.

•	Tighten the camshaft bearing caps 2-5 in a spiral from the inside to the outside.

Tighten
Tighten the camshaft bearing caps 8 N·m (70 lb in).





Note: Sealing surfaces must be free from oil and grease.

4. Clean sealing surfaces of the 1st camshaft bearing support and the cylinder head with a suitable tool, e.g. plastic wedge.

Clean oil duct (arrow) from any sealant residue.





Note: 

•	It is essential to ensure that no sealant is applied outside the marked sealing areas.

•	The grooves (1) adjacent to the sealing surfaces must remain free from sealant.

5. Apply surface sealant (green) to sealing surfaces (arrows) of the 1st camshaft bearing support thinly and evenly.
6. Position the camshaft bearing bridge on the cylinder block and tighten the bolts hand tight, approximately 2 N·m (18 lb in).



7. Install the 2 camshaft seal rings.

•	Tighten the seal ring with KM-422 (4) on the camshaft until this is in contact with the cylinder head (arrow).

•	To install, use camshaft sprocket bolt (1) in conjunction with shims (2) with a total thickness of approximately 10 mm.

•	Remove KM-422 .

•	Remove the bolt.





Note: No sealant may reach the camshafts.

8. Attach the 1st camshaft bearing support.

•	Place bearing support in position.

Tighten
Tighten the 4 bolts to 8 N·m (70 lb in).

•	Note installation sequence 1-4.

9. Insert MK-6628 .

•	Turn the intake camshaft against the direction of engine rotation

Insert MK-6628 .

•	Turn the exhaust camshaft in the direction of rotation of the engine.

Insert MK-6628 .

10. Install the rear toothed belt cover. Refer to Timing Belt Rear Cover Replacement.