GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2009 🢒 Astra 🢒 Safety and Security 🢒 Supplemental Inflatable Restraints 🢒 DTC C0292

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C0292 1A: VSES Combination Sensor Circuits Bias Level Out of Range

DTC C0292 39: VSES Combination Sensor Circuits Internal Electronic Failure

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Ignition Voltage

C0292 1A

C0292 1A

C0292 1A

C0292 39*

Low Reference

C0292 1A

C0292 1A

--

C0292 39*

CAN Bus High Serial Data

C0292 1A

C0292 1A

C0292 1A

C0292 39*

CAN Bus Low Serial Data

C0292 1A

C0292 1A

C0292 1A

C0292 39*

* Internal Sensor Failure

Circuit/System Description

The electronic brake control module (EBCM) monitors and supplies a 12 volt reference to the yaw sensor with vehicle lateral and longitudinal accelerometer.

Conditions for Running the DTC

Ignition ON.

Conditions for Setting the DTC

DTC C0292 1A

    • The EBCM detects the sensor voltage is above 18 volts
    • The EBCM detects the sensor voltage is below 6 volts

DTC C0292 39

Internal failure of the yaw sensor with vehicle lateral and longitudinal accelerometer.

Action Taken When the DTC Sets
    • The EBCM disables vehicle stability enhancement system (VSES) and sends a serial data message to the DIC.
    • The VSES indicator illuminates.
    • The driver information center (DIC) illuminates the warning indicator/message.

Conditions for Clearing the DTC
    • The condition for setting the DTC is no longer present.
    • The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Reference Information

Schematic Reference

Antilock Brake System Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

ABS Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

DTC C0292 39

Ignition On, verify that DTC  C0292 39 is not set.

⇒If the DTC is set, replace the yaw sensor with vehicle lateral and longitudinal accelerometer.

DTC C0292 1A

  1. Ignition OFF, disconnect the harness connector at the yaw sensor with vehicle lateral and longitudinal accelerometer.
  2. Ignition OFF,test for less than 5 ohms between the low reference circuit terminal 5 and ground.
    3. ⇒If greater than the specified range, test for an open/high resistance in the low reference circuit. If the circuit tests normal, replace the EBCM.
  3. Ignition ON, test for B+ between the ignition circuit terminal 3 and ground.
    4. ⇒If less than the specified range, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the EBCM.
  4. Ignition OFF, disconnect the harness connector at the EBCM.
  5. Ignition ON, test for less than 1 volt between the CAN bus low circuit terminal 1 and ground at the yaw rate/lateral accelerometer sensor connector.
    6. ⇒If greater than the specified range, test the CAN bus low circuit for a short to voltage.
  6. Ignition OFF, test for infinite resistance between the CAN bus low circuit terminal 1 and ground.
    7. ⇒If less than the specified value, test the CAN bus low circuit for a short to ground.
  7. Ignition ON, test for less than 1 volt between the CAN bus high circuit terminal 2 and ground at the yaw rate/lateral accelerometer sensor connector.
    8. ⇒If greater than the specified range, test the CAN bus high circuit for a short to voltage.
  8. Ignition OFF, test for infinite resistance between the CAN bus high circuit terminal 2 and ground.
    9. ⇒If less than the specified value, test the CAN bus high circuit for a short to ground.
  9. Ignition OFF, test for infinite resistance between the CAN bus high circuit terminal 2 and the CAN bus low circuit terminal 1at the yaw rate/lateral accelerometer sensor connector.
    10. ⇒If less than the specified value, test the CAN bus circuits for a short to each other.
  10. If all circuits test normal, replace the yaw sensor with vehicle lateral and longitudinal accelerometer.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Vehicle Yaw Sensor with Vehicle Lateral and Longitudinal Accelerometer Replacement
    •  Control Module References for EBCM replacement, setup, and programming