GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2003 🢒 ION 🢒 Engine 🢒 Engine Controls - 2.2L (L61) 🢒 DTC P0172

Circuit Description

The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy, and emission control. Fuel delivery is controlled differently during Open Loop and Closed Loop. During Open Loop, the ECM determines fuel delivery based on sensor signals, without heated oxygen sensor (HO2S) input. During Closed Loop, the HO2S inputs are added and used by the ECM to calculate the short and long term fuel trim (FT). If the HO2S indicates a lean condition, the FT values will be above 0 percent. If the HO2S indicate a rich condition, the FT values will be below 0 percent. The short term FT values change rapidly in response to the HO2S voltage signals. The long term FT makes coarse adjustments in order to maintain an Air/Fuel Ratio of 14.7:1. The FT diagnostic will conduct a test to determine if a rich failure actually exists or if excessive vapor from the evaporative emission (EVAP) canister is causing a rich condition. If the ECM detects an excessively rich condition, DTC P0172 sets.

DTC Descriptor

This diagnostic supports the following DTC:

DTC P0172 Fuel Trim System Rich

Conditions for Running the DTC
    • DTCs P0037, P0038, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0125, P0130 , P0131, P0132, P0133, P0134, P0137, P0138, P0140, P0141, P0300, P0336, P0340, P0341, P0401, P0404, P0405, P0455, P0500, P0506, P0507, P0601, P0602, P0606, P0641, P1133, P1134 are not set.
    • The engine coolant temperature (ECT) is 60-115°C (140-239°F).
    • The intake air temperature (IAT) is -20 to +80°C (-4 to +176°F).
    • The manifold absolute pressure (MAP) is between 30-90 kPa (4.4-13 psi).
    • The mass air flow (MAF) is 2-80 g/s.
    • The engine speed is between 500-4,000 RPM.
    • The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
    • The throttle angle is less than 75 percent.
    • DTC P0172 runs continuously once the above conditions have been met.

Conditions for Setting the DTC
    • The average long term FT is less than -25 percent.
    • The above condition is present for 2 minutes.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
    • Fuel contamination, such as water and alcohol, will affect the FT.
    • A rich condition can result if the injectors are supplying too much fuel.
    • Review the Failure Records with a scan tool. If an intermittent condition is suspected , refer to Intermittent Conditions .

Test Description

The number below refers to the step number on the diagnostic table.

  1. An EVAP canister that is saturated will cause a rich condition. If conditions were not corrected, a worn cam, worn intake or exhaust valves or other engine mechanical failure may be at fault.

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If any DTCs are set other than P0172, refer to those DTCs before proceeding with this diagnostic.

  1. Install a scan tool.
  2. Review the Freeze Frame/Failure Records and record displayed data for this DTC.
  3. Select Fuel and Emission parameter.
  4. Start the engine.
  5. Observe the Long Term FT parameter with a scan tool.

Is the Long Term FT parameter less than the specified value?

-25%

Go to Step 3

Go to Diagnostic Aids

3
  1. Start the engine.
  2. Allow the engine to reach operating temperature.
  3. Put the transmission in PARK or NEUTRAL position.
  4. Turn off all of the accessories.
  5. Allow the engine to idle.
  6. Observe the Manifold Absolute Pressure (MAP) sensor parameter with a scan tool.

Is the MAP sensor parameter within the specified range?

19-42 kPa

Go to Step 4

Go to DTC P0106

4
  1. Operate the engine at idle.
  2. Observe the heated oxygen sensor (HO2S) parameters with a scan tool.

Does the scan tool indicate that the values are within the specified range and fluctuating?

200-800 mV

Go to Step 5

Go to Step 6

5
  1. Turn OFF the engine.
  2. Visually and physically inspect the following items:
    3. • Vacuum hoses for splits, kinks, and proper connections--Refer to Emission Hose Routing Diagram .
    • 
    • The air intake duct for being collapsed or restricted
    • The air filter for being dirty or restricted
    • For objects blocking throttle body

Did you find and correct the condition?

--

Go to Step 8

Go to Step 7

6
  1. Turn OFF the engine.
  2. Inspect for the following conditions:
    3. • The HO2S for proper installation
    • Ensure that the electrical connectors and wires are secured and not contacting the exhaust system.
    • The HO2S signal circuit for a short to voltage--Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 8

Go to Fuel System Diagnosis

7

Inspect for the following:

    • Excessive fuel in the crankcase
    • The evaporative emissions (EVAP) control system for proper operation
    • The fuel system for proper operation--Refer to Fuel System Diagnosis .
    • Ensure that all injectors are functioning properly. Refer to Fuel Injector Solenoid Coil Test .

Did you find and correct the condition?

--

Go to Step 8

Go to Symptoms - Engine Mechanical in Engine Mechanical

8

Important: After repairs, use the scan tool Fuel Trim Reset function in order to reset the Long Term Fuel Trim.

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 9

9

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK