Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

Important: Inspect the fuel system for damage or external leaks before proceeding with this diagnostic.

1. Turn ON the ignition, with the engine OFF.
2. Command the fuel pump relay ON with a scan tool.

Does the fuel pump operate?

--

Go to Step 3

Go to Fuel Pump Electrical Circuit Diagnosis

Important: Verify that adequate fuel is in the fuel tank before proceeding with this diagnostic.

1. Turn OFF the ignition.
2. Turn OFF all accessories.
3. Install the SA9127E Gage Bar Set with the Fuel Pressure Adapter and the Drain Hose. Refer to Fuel Pressure Gage Installation and Removal .
4. Turn ON the ignition, with the engine OFF.

Important: DO NOT start the engine.

5. Command the fuel pump relay ON with a scan tool.
6. Observe the fuel pressure gage with the fuel pump commanded ON.

Is the fuel pressure within the specified range?

345-414 kPa (50-60 psi)

Go to Step 5

Go to Step 4

Is the fuel pressure more than the specified value?

414 kPa (60 psi)

Go to Step 8

Go to Step 9

Important: The fuel pressure may vary slightly when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.

Monitor the fuel pressure gage for 5 minutes.

Does the fuel pressure decrease by more than the specified value?

55 kPa (8 psi)

Go to Step 7

Go to Step 6

1. Operate the vehicle within the conditions to reproduce the original symptoms.
2. Monitor the O2 and the Fuel Trim parameters with a scan tool.

Do the scan tool parameters indicate a lean condition?

--

Go to Step 9

Go to Symptoms - Engine Controls

1. Turn OFF the ignition.
2. Relieve the fuel pressure. Refer to Fuel Pressure Relief .
3. Remove the fuel pressure gage from the fuel pressure test connection.
4. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Disconnect the fuel feed pipe and the fuel return pipe from the fuel filter. Refer to Plastic Collar Quick Connect Fitting Service .
6. Connect the fuel feed pipe to the inlet side of SA9127E-7 Fuel Pressure/Flow Adapter.
7. Connect the fuel return pipe to the ON/OFF valve side of the SA9127E-7 .
8. Connect the fuel pressure gage to the SA9127E-7 .
9. Open the valve on the SA9127E-7 .
10. Turn ON the ignition, with the engine OFF.
11. Command the fuel pump relay ON for a minimum of 10 seconds with a scan tool.
12. Close the valve on the SA9127E-7 .
13. Monitor the fuel pressure gage for 5 minutes.

Does the fuel pressure decrease by more than the specified value?

55 kPa (8 psi)

Go to Step 12

Go to Step 11

Inspect the return side of the fuel filter for a restriction.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 12

Inspect the following components for a restriction:

Did you find and correct the condition?

--

Go to Step 13

Go to Step 10

Inspect the harness connectors and the ground circuits of the fuel pump for poor connections. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 12

1. Turn OFF the ignition.
2. Raise the fuel rail with the fuel pipe connected. Refer to Fuel Injection Fuel Rail Assembly Replacement .
3. Turn ON the ignition, with the engine OFF.
4. Command the fuel pump relay ON with a scan tool.
5. Locate and replace the leaking fuel injector. Refer to Fuel Injector Replacement .

Did you complete the replacement?

--

Go to Step 13

--

Replace the fuel pump module. Refer to Fuel Pump Module Replacement .

Did you complete the replacement?

--

Go to Step 13

--

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 3