Air Conditioning Compressor Replacement 2.2L (L61), 2.4L (LE5)

Tools Required

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the right side engine splash shield. Refer to Engine Splash Shield Replacement in Body Front End.



4. Use J 44811 to rotate the drive belt tensioner counterclockwise to release the spring tension.
5. Remove the drive belt.



6. Disconnect the electrical connector from the compressor.



7. Remove the compressor and condenser hose assembly bolt from the compressor.
8. Remove the compressor and condenser hose assembly from the compressor.
9. Remove and discard the sealing washers.



10. Remove the compressor mounting bolts.
11. Remove the compressor.

Notice: Do NOT mix refrigerant oils. Use of incorrect refrigerant oil will cause compressor failure. This compressor uses a low viscosity refrigerant oil, Saturn P/N 22695048.

Important: NEW CVC compressor assemblies are shipped with a partial poly-alkylene glycol (PAG) refrigerant oil charge. Use of the incorrect PAG oil can result in compressor failure.

1. If you are replacing the compressor, refer to Air Conditioning Compressor Oil Balancing .

Notice: Refer to Fastener Notice in the Preface section.




2. Install the compressor and the bolts to the engine.

Tighten
Tighten the bolts to 22 N·m (16 lb ft).




3. Install new sealing washers on the hose fittings. Refer to Sealing Washer Replacement .
4. Install the hose assembly to the compressor.
5. Install the assembly bolt.

Tighten
Tighten the bolt to 20 N·m (15 lb ft).




6. Connect the compressor electrical connector.



7. Use J 44811 to rotate the drive belt tensioner counterclockwise to release the spring tension.
8. Install the drive belt.
9. Install the right side engine splash shield. Refer to Engine Splash Shield Replacement in Body Front End.
10. Lower the vehicle.
11. Evacuate and charge the refrigerant system. Refer to Refrigerant Recovery and Recharging .
12. Leak test the fittings using J 39400-A .

Air Conditioning Compressor Replacement 2.0L (LSJ)

Tools Required

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the right front fender liner. Refer to Front Fender Liner Replacement in Body Front End.
4. Remove the drive belt. Refer to Drive Belt Replacement .



5. Disconnect the electrical connector from the compressor.



6. Remove the compressor and condenser hose assembly bolt from the compressor.
7. Remove the compressor and condenser hose assembly from the compressor.
8. Remove and discard the sealing washers.



9. Remove the auxiliary intercooler pump bolts and position the pump toward the driver side of the vehicle.



10. Remove the compressor mounting bolts.
11. Remove the compressor.

Notice: Do NOT mix refrigerant oils. Use of incorrect refrigerant oil will cause compressor failure. This compressor uses a low viscosity refrigerant oil, Saturn P/N 22695048.

Important: NEW CVC compressor assemblies are shipped with a partial poly-alkylene glycol (PAG) refrigerant oil charge. Use of the incorrect PAG oil can result in compressor failure.

1. If you are replacing the compressor, refer to Compressor Oil Balancing .

Notice: Refer to Fastener Notice in the Preface section.




2. Install the compressor and the bolts to the engine.

Tighten
Tighten the bolts to 22 N·m (16 lb ft).




3. Install new sealing washers on the hose fittings. Refer to Sealing Washer Replacement .
4. Install the hose assembly to the compressor.
5. Install the assembly bolt.

Tighten
Tighten the bolt to 20 N·m (15 lb ft).




6. Connect the compressor electrical connector.



7. Install the auxiliary intercooler pump.

Tighten
Tighten the pump bolt to 10 N·m (88 lb in).




8. Use J 44811 to rotate the drive belt tensioner counterclockwise to release the spring tension.
9. Install the drive belt.
10. Install the front fender liner. Refer to Front Fender Liner Replacement in Body Front End.
11. Lower the vehicle.
12. Evacuate and charge the refrigerant system. Refer to Refrigerant Recovery and Recharging .
13. Leak test the fittings using J 39400-A .