Circuit Description
The throttle position (TP) sensors 1 and 2 are located within the throttle body assembly. Each sensor has the following components:
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
This provides the powertrain control module (PCM) with a signal voltage proportional to throttle plate movement. TP sensor 1 signal voltage at closed throttle is near the 5-volt reference and decreases as the throttle plate is opened. TP sensor 2 signal voltage at closed throttle is near the low reference and increases as the throttle plate is opened. When TP sensor 2 signal voltage is not within the predicted range, this DTC sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0220 Throttle Position (TP) Sensor 2 Circuit
Conditions for Running the DTC
| • | The ignition switch in the Crank or Run position. |
| • | DTC P0641 is not set. |
| • | The ignition voltage is more than 5.23 volts. |
| • | DTC P0220 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
The TP sensor 2 voltage is less than 0.31 volt or more than 4.7 volts for more than 0.4 second.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic runs and passes. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate voltage less than the first value or greater than the second value? | 0.31 V 4.7 V | Go to Step 4 | Go to Step 3 |
3 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions |
4 |
Does the scan tool indicate voltage at the specified value? | 5 V | Go to Step 5 | Go to Step 13 |
5 | With a test lamp connected to ground, probe the TP sensor 2 signal circuit. Does the test lamp illuminate? | -- | Go to Step 12 | Go to Step 6 |
6 | Observe the TP sensor 2 parameter with a test lamp still connected to the TP sensor 2 signal circuit. Does the scan tool indicate voltage at the specified value? | 0 V | Go to Step 7 | Go to Step 11 |
7 | Measure the voltage of the TP sensor 2 5-volt reference circuit with a DMM. Does the DMM indicate voltage at the specified value? | 5 V | Go to Step 8 | Go to Step 10 |
8 | Measure the resistance of the low reference circuit of the TP sensor 2 with a DMM. Refer to Circuit Testing . Is the resistance less than the specified value? | 5ohms | Go to Step 9 | Go to Step 14 |
9 | Test the TP sensor 2 low reference circuit for a short to ground. Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 18 |
10 | Does the DMM indicate voltage less than the specified value on the TP sensor 2 5-volt reference circuit? | 5 V | Go to Step 15 | Go to Step 17 |
11 | Test the TP sensor 2 signal circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 13 |
12 | Test the TP sensor 2 signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
13 | Test the TP sensor 2 signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
14 | Test the TP sensor 2 low reference circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
15 | Test the TP sensor 2 5-volt reference circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 16 |
16 | Test the TP sensor 2 5-volt reference circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
17 | Test the TP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
18 | Inspect for poor connections at the throttle body harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 19 |
19 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 22 | -- |
20 | Inspect for poor connections at the powertrain control module (PCM) harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 21 |
21 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 22 | -- |
22 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 23 |
23 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
