GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2005 🢒 ION 🢒 Restraints 🢒 SIR 🢒 DTC B2707

Object Number: 896504 Size: MF

Circuit Description

The body control module (BCM) controls the automatic transmission (A/T) shift lock control solenoid by providing battery voltage to the solenoid. The BCM utilizes a smart driver to control the voltage supplied to the A/T shift lock control solenoid. The smart driver monitors the voltage and current flow of the control circuit. DTC B2707 will set when the BCM detects a short to ground, during the shift lock control solenoid operation.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B2707 Gearshift Unlock Circuit Low

Conditions for Running the DTC
    • The ignition switch is in the ON position.
    • The brake pedal is depressed.
    • The transmission the PARK position.

Conditions for Setting the DTC

The BCM detects the shift lock control solenoid control circuit is grounded for a minimum of one second.

Action Taken When the DTC Sets

The BCM disables shift lock control solenoid operation until the next key cycle.

Conditions for Clearing the DTC
    • A current DTC B2707 will clear when the malfunction is no longer present and the ignition switch is cycled.
    • All BCM history codes will clear after 100 ignition cycles with no current codes active during the 100 ignition cycles.

Diagnostic Aids
    • If the A/T shift lock control circuit is shorted to ground, the A/T shift lock control solenoid will be inoperative. The shift lever will not shift out of PARK position with the brake pedal depressed.
    • Perform the tests while wiggling the wires and connectors. This may often cause an intermittent malfunction to appear. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Listen for an audible click when the A/T shift lock control solenoid operates. Command both the ON and OFF states. Repeat the commands, as necessary.

    2.

  2. Tests for voltage at controlled voltage supply circuit of the A/T shift lock control solenoid.

Step

Action

Yes

No

Schematic Reference: Shift Lock Control Schematics

Connector End View Reference: Computer/Integrating Systems Connector End Views in Computer/Integrating Systems

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the brake to shift relay output control ON and OFF.

Does the automatic transmission (A/T) shift lock control solenoid turn ON and OFF with each command?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the A/T shift lock control solenoid.
  3. Connect a test lamp between the shift lock solenoid control circuit at the connector of the A/T shift lock solenoid and a good ground.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, command the brake to shift relay output control ON and OFF several times.

Does the test lamp illuminate ON and OFF with each command?

Go to Step 5

Go to Step 4

4

Test the control circuit of the A/T shift lock control solenoid for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 6

5

Inspect for poor connections at the harness connector of the A/T shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 7

6

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

Replace the A/T shift lock control solenoid. Refer Shift Lock Control Solenoid Replacement .

Did you complete the replacement?

Go to Step 9

--

8

Important: Perform the set up procedures for the BCM.

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 9

--

9
  1. Use the scan tool in order to clear the DTCs .
  2. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK