Important: Failure to follow this procedure will compromise the structural integrity of the vehicle.

The front of the dash panel and plenum lower are formed from laminated steel. This steel is constructed by bonding 2 pieces of cold rolled steel with a viscosities layer of adhesive. MIG welding laminated steel does not meet GM Corporate standards for structural integrity. As an alternative, all factory welds may be replaced by using the rivet and adhesive bond method described in the installation portion of this procedure. The rivet and adhesive bond method must only be used in the areas described in this procedure.

Caution: Refer to Approved Equipment for Collision Repair Caution in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.



3. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint/Coatings.
4. Visually inspect the damaged area. Repair as much of the damage as possible. Refer to Dimensions - Body .

Important: Drill through the front inner hinge pillar flange only. Do not drill into the dash panel.




5. Using an 8 mm (5/16 in) spot weld remover, locate and drill out the factory welds on the weld flange connecting the front inner hinge pillar to the dash panel.




Important: Note the number and location of welds for installation of the front inner hinge pillar.

6. Locate and drill out all remaining factory welds.



7. Remove the front inner hinge pillar from the vehicle.

1. Position the service front inner hinge pillar in the vehicle using 3-dimensional measuring equipment. Clamp the front inner hinge pillar in place.



2. Using a 7 mm (17/64 in) bit, drill the rivet attachment holes through the dash and the lower rail extension in the locations as noted from the factory front inner hinge pillar.



3. Remove the service front inner hinge pillar.

Important: If the location of the original plug weld holes can not be determined, space the plug weld holes every 40 mm (1 1/2 in) apart.

4. Drill 8 mm (5/16 in) plug weld holes as necessary in the locations noted from the original assembly.
5. Prepare the MIG weld mating surfaces as necessary.
6. Apply 3M Weld-Thru Coating P/N 05916 or equivalent to all MIG weld mating surfaces.




Important: Do not damage the corners or thin the metal during the grinding process.

7. Prepare the bonding mating areas by grinding to bare steel the surface of the dash panel and rail extension to the service front inner hinge pillar flanges.



8. Apply a 3-6 mm (1/8-1/4 in) bead of metal panel bonding adhesive P/N 12378567 (Canadian P/N 88901675) or equivalent to the mating surfaces of the dash panel and the rail extension, and the front inner hinge pillar service panel.



9. Using a small acid brush, spread a coating of adhesive on the mating surfaces. Cover all of the bare metal to ensure corrosion protection.

Important: Do not pull the front inner hinge pillar off of the dash after adhesion. To align the parts, slide the front inner hinge pillar against the dash panel.

10. Position the service front inner hinge pillar to the vehicle using 3-dimensional measuring equipment. Clamp the front inner hinge pillar in place.




Important: Verify the proper positioning of the service front inner hinge pillar prior to riveting and welding.

11. Install the 14 mm (17/32 in) long rivets so that the rivet head contacts the rail extension.



12. Install the 9 mm (11/32 in) long rivets so that the rivet head contacts the dash panel.
13. Remove the excess adhesive from the front inner hinge pillar bond rivet area.



14. Plug weld accordingly.
15. Clean and prepare all of the welded surfaces.
16. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint/Coatings.
17. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems in Paint/Coatings.
18. Install all related panels and components.
19. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
20. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.