Circuit Description
The commanded throttle position (TP) is compared to the actual TP based on the accelerator pedal position (APP) and possibly other limiting factors. Both values should be within a calibrated range of each other. The engine control module (ECM) continuously monitors the commanded and actual throttle positions. This DTC sets if the values are greater than the calibrated range.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P2101 Throttle Actuator Position Performance
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The ignition voltage is greater than 8 volts. |
| • | The system is not in Battery Saver mode. |
| • | The engine is running. |
| • | DTC P0068 is not set. |
| • | DTC P2101 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
| • | The difference between the predicted and the actual TP is more than a calibrated amount. |
| • | The above condition is present for more than 0.6 second. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The ECM turns OFF the MIL after 3 consecutive drive trips that the diagnostic runs and passes. |
| • | A History DTC clears after 40 consecutive warm-up cycles in which there are no failures reported of this diagnostic or any other emission related diagnostic. |
| • | The scan tool clears the MIL/DTC. |
Diagnostic Aids
| • | A low voltage condition may set this DTC. Reviewing the Freeze Frame/Failure Records may be beneficial in diagnosing this concern. |
| • | This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test . |
| • | A powertrain relay that is slow to switch on may set this DTC. Inspect the relay thoroughly |
| • | A low voltage condition may set this DTC Inspect for proper battery voltage and correct charging system operation. |
| • | The throttle valve is spring loaded to a slightly open position. This is referred to as the rest position. |
| • | The throttle valve should not be completely closed nor should they be open any more than the specified amount. |
| • | The throttle valve should move open and to the closed position without binding under the normal spring pressure. |
| • | The throttle should NOT be free to move open or closed WITHOUT spring pressure. |
| • | Replace the throttle body if any of these conditions are found. |
Important: Operating the throttle blade with the Throttle Blade Control function of the scan tool may cause additional DTCs to set. Do not attempt to diagnose DTCs set during this function.
| • | The scan tool has the ability to operate the throttle control system using Special Functions. Actuate the throttle valve using the throttle blade control function located in the Throttle Actuator Control (TAC) System menu. This function will operate the throttle valve through the entire range in order to determine if the throttle body and system operate correctly. |
| • | Inspect for the following conditions: |
| - | Use the J 35616 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. |
| - | Poor connections at the ECM or at the component--Inspect the harness connectors for a poor terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections for the proper procedure. |
| - | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
The throttle valve is spring loaded in a slightly open position and should move in either direction without binding. The throttle valve should always be under spring pressure.
-
When the ignition is turned ON, the ECM operates the throttle control motor to verify the integrity of the system prior to start-up. This can be seen by the momentary flash of the test lamp as the ignition is turned ON.
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||||||
2 | Are DTCs P0120, P0220, P2120, P2125, P2135, P2138 also set? | -- | Go to Step 3 | |||||||||
3 |
Important: The throttle angle and pedal angle may not correspond during this procedure.
Does the TP Sensor 1 and 2 Angle parameters increase as the pedal is applied and decrease as the pedal is released? | -- | Go to Step 4 | Go to Step 5 | ||||||||
4 |
Did the DTC fail this ignition? | -- | Go to Step 5 | Go to Diagnostic Aids | ||||||||
5 |
Does the test lamp illuminate on both sides of the fuse? | -- | Go to Step 6 | Go to Step 15 | ||||||||
6 |
Does the test lamp illuminate on both sides of the fuse? | -- | Go to Step 22 | Go to Step 7 | ||||||||
7 |
Is the resistance less than the specified value? | 5 ohms | Go to Step 8 | Go to Step 23 | ||||||||
Did you find any of these conditions with the throttle body? | -- | Go to Step 24 | Go to Step 9 | |||||||||
9 |
Important: The test lamp may momentarily flash when testing these circuits. This is considered normal.
Did the test lamp illuminate and remain illuminated on either circuit? | -- | Go to Step 12 | Go to Step 10 | ||||||||
10 |
Important: The test lamp may momentarily flash when testing these circuits. This is considered normal. Probe the TAC motor control 1 and 2 circuits with the test lamp connected to battery positive. Did the test lamp illuminate and remain illuminated on either circuit? | -- | Go to Step 13 | Go to Step 11 | ||||||||
Does the test lamp flash ON and then turn OFF? | -- | Go to Step 12 | Go to Step 14 | |||||||||
12 |
Does the test lamp illuminate? | -- | Go to Step 20 | Go to Step 19 | ||||||||
13 |
Does the test lamp illuminate? | -- | Go to Step 21 | Go to Step 19 | ||||||||
14 |
Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 19 | ||||||||
15 | Test the ignition 1 voltage circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 17 | ||||||||
16 | Test the motor control 1 circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 24 | ||||||||
17 |
Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 18 | ||||||||
18 | Test for a poor connection or terminal tension at the throttle body connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 24 | ||||||||
19 | Test for a poor connection or terminal tension at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 24 | ||||||||
20 | Repair the short to voltage on the circuit where the test lamp remained illuminated. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 26 | -- | ||||||||
21 | Repair the short to ground on the circuit where the test lamp remained illuminated. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 26 | -- | ||||||||
22 | Repair the short to voltage on the ignition 1 voltage circuit. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 26 | -- | ||||||||
23 | Repair the open or high resistance in the ignition 1 voltage circuit. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 26 | -- | ||||||||
24 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 26 | -- | ||||||||
25 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 26 | -- | ||||||||
26 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 27 | ||||||||
27 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |||||||||
