Circuit Description
The transmission control module (TCM) uses the pressure control (PC) solenoid valve in order to regulate the transmission line pressure. The PC solenoid valve consists of an electrical connector, a coil, an armature, a regulating spring, and a poppet valve. The PC solenoid valve is attached to the control valve body. The TCM compares TP voltage, fluid temperature, gear states, and other inputs in order to determine the line pressure appropriate for a given load. The TCM regulates the pressure by applying a varying amperage to the PC solenoid valve. The applied amperage varies from 0.1 amps for maximum line pressure to 1.1 amps for minimum line pressure. The TCM then monitors the amperage at the return line.
When the TCM detects a continuous open, short to ground or short to voltage in the PC solenoid valve circuit, then DTC P0961 sets. DTC P0961 is a type C DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0961 Line Pressure Control (PC) Solenoid System Performance
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The TCM detects a continuous short to ground, open, or short to voltage in the PC solenoid or the PC solenoid circuits.
Action Taken When the DTC Sets
| • | The TCM does not request the ECM to illuminate the malfunction indicator lamp (MIL). |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
| • | The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records. |
| • | The TCM stores DTC P0961 in TCM history. |
Conditions for Clearing the DTC
| • | A scan tool can clear the DTC. |
| • | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
| • | The TCM cancels the DTC default actions when the fault no longer exists and the DTC passes. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies the ability of the TCM to command the PC solenoid valve.
-
This step verifies that the automatic transmission wiring harness and the PC solenoid valve have correct resistance.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
Important: Before clearing the DTC, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the TCM. Does the PC Sol. Actual Current differ from the PC Sol. Ref. Current by more than the specified amount? | 0.16 amps | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections | |
Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance within the specified range? | 3-7 ohms | Go to Step 7 | Go to Step 4 | |
4 | Is the resistance greater than the specified value? | 7 ohms | Go to Step 5 | Go to Step 6 |
5 |
Refer to Testing for Continuity . Did you find a condition? | -- | Go to Step 19 | Go to Step 20 |
6 | Test the high control circuit and the low control circuit of the PC solenoid valve for being shorted together between the AT inline 20-way connector and the PC solenoid valve. Refer to Circuit Testing . Did you find a condition? | -- | Go to Step 19 | Go to Step 20 |
7 | Measure the resistance from the PC solenoid valve high control circuit of the J 44152 to ground. Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 1,000 ohms | Go to Step 8 | Go to Step 9 |
8 |
Refer to Testing for Short to Ground . Did you find a condition? | -- | Go to Step 19 | Go to Step 20 |
9 | Measure the resistance between the PC solenoid valve high control circuit and all other terminals except the PC solenoid valve low control circuit of the J 44152 . Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance between less than the specified value? | 10 ohms | Go to Step 19 | Go to Step 10 |
10 |
Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 10 ohms | Go to Step 11 | Go to Step 12 |
11 | Test the low control circuit of the PC solenoid valve for a short to ground between the TCM connector and the AT inline 20-way connector. Refer to Testing for Short to Ground and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
12 | Using the DMM and the J-35616 connector test adapter kit, measure the resistance of the PC solenoid valve low control circuit between the J 44152 and the TCM connector. Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 10 ohms | Go to Step 14 | Go to Step 13 |
13 | Test the low control circuit of the PC solenoid valve for an open between the TCM connector and the AT inline 20-way connector. Refer to Testing for Continuity and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
14 | Using the DMM and the J-35616 connector test adapter kit, measure the resistance from the PC solenoid valve high control circuit of the J 44152 to a good ground. Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 10 ohms | Go to Step 15 | Go to Step 16 |
15 | Test the high control circuit of the PC solenoid valve for a short to ground between the TCM connector and the AT inline 20-way connector. Refer to Testing for Short to Ground and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
16 | Using the DMM and the J-35616 connector test adapter kit, measure the resistance of the PC solenoid valve high control circuit between the J 44152 and the TCM connector. Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 10 ohms | Go to Step 17 | Go to Step 18 |
17 | Test the high control circuit and the low control circuit of the PC solenoid for a short to voltage. Refer to Testing for a Short to Voltage and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 21 |
18 | Test the high control circuit of the PC solenoid valve for an open between the TCM connector and the AT inline 20-way connector. Refer to Testing for Continuity and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
19 | Replace the automatic transmission wiring harness. Refer to Wiring Harness Replacement . Did you complete the replacement? | -- | Go to Step 22 | -- |
20 | Replace the PC solenoid valve. Refer to Pressure Control Solenoid Valve Replacement . Did you complete the replacement? | -- | Go to Step 22 | -- |
21 | Replace the TCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 22 | -- |
22 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 23 | Go to Step 2 |
23 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |
