DTC P0719 2.0L - With Manual Transmission
Circuit Description
The cruise release switch is a normally closed switch. The stop lamp switch signal circuit is a normally open switch. When the brake pedal is released, the powertrain control module (PCM) detects a high voltage signal on the torque converter clutch (TCC) brake switch/cruise control release signal circuit and a low signal voltage signal on the stop lamp switch signal circuit.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0719 Brake Switch Circuit Low Voltage
Conditions for Running the DTC
| • | The engine is ON. |
| • | The traction control system or the antilock brake system are not active and have not failed. |
| • | The vehicle has accelerated from 0 km/h (0 mph) to 60 km/h (37 mph) 3 times in one ignition cycle. |
| • | This diagnostic runs continuously once the conditions for running the DTC has been achieved. |
Conditions for Setting the DTC
When the brake pedal is released, the PCM detects a low voltage signal on the stop lamp switch signal circuit and a low voltage signal on the TCC brake switch/cruise control release signal circuit.
Action Taken When the DTC Sets
| • | The PCM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The PCM stores this information in the Failure Records. |
| • | The cruise control system is disabled. |
Conditions for Clearing the DTC
| • | A last test failed, or current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC will clear after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Use a scan tool in order to clear the DTC. |
Diagnostic Aids
In order to avoid a misdiagnosis, inspect for proper adjustment of the cruise control release switch. Refer to Cruise Release Switch Adjustment .
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Cruise Control Schematics Connector End View Reference: Lighting Systems Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the test lamp illuminate? | -- | Go to Step 3 | Go to Step 7 |
3 |
Does the resistance of the cruise release switch measure at the specified value? | O.L. | Go to Step 5 | Go to Step 4 |
4 | Test the TCC brake switch/cruise control release signal circuit for an open, for a high resistance, or for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the cruise release switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 | Repair the open, the high resistance, or the short to ground in the ignition 1 voltage circuit. Refer to Circuit Testing and Wiring Repairs . Did you complete the repair? | -- | Go to Step 10 | -- |
8 | Replace the cruise release switch. Refer to Cruise Control Release Switch Replacement . Did you complete the repair? | -- | Go to Step 10 | -- |
9 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
DTC P0719 non 2.0L - With Manual Transmission
Circuit Description
The cruise release switch is a normally closed switch. The stop lamp switch signal circuit is a normally open switch. When the brake pedal is released, the engine control module (ECM) detects a high voltage signal on the torque converter clutch (TCC) brake switch/cruise control release signal circuit and a low signal voltage signal on the stop lamp switch signal circuit.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0719 Brake Switch Circuit Low Voltage
Conditions for Running the DTC
| • | The engine is ON. |
| • | The traction control system or the antilock brake system are not active and have not failed. |
| • | The vehicle has accelerated from 0 km/h (0 mph) to 60 km/h (37 mph) 3 times in one ignition cycle. |
| • | This diagnostic runs continuously once the conditions for running the DTC has been achieved. |
Conditions for Setting the DTC
When the brake pedal is released, the ECM detects a low voltage signal on the stop lamp switch signal circuit and a low voltage signal on the TCC brake switch/cruise control release signal circuit.
Action Taken When the DTC Sets
| • | The ECM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The ECM records the operating conditions at the time the diagnostic fails. The ECM stores this information in the Failure Records. |
| • | The cruise control system is disabled. |
Conditions for Clearing the DTC
| • | A last test failed, or current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC will clear after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Use a scan tool in order to clear the DTC. |
Diagnostic Aids
In order to avoid a misdiagnosis, inspect for proper adjustment of the cruise control release switch. Refer to Cruise Release Switch Adjustment .
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Cruise Control Schematics Connector End View Reference: Lighting Systems Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the test lamp illuminate? | -- | Go to Step 3 | Go to Step 7 |
3 |
Does the resistance of the cruise release switch measure at the specified value? | O.L. | Go to Step 5 | Go to Step 4 |
4 | Test the TCC brake switch/cruise control release signal circuit for an open, for a high resistance, or for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the cruise release switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 | Repair the open, the high resistance, or the short to ground in the ignition 1 voltage circuit. Refer to Circuit Testing and Wiring Repairs . Did you complete the repair? | -- | Go to Step 10 | -- |
8 | Replace the cruise release switch. Refer to Cruise Control Release Switch Replacement . Did you complete the repair? | -- | Go to Step 10 | -- |
9 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
