GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2006 🢒 ION 🢒 Restraints 🢒 SIR 🢒 DTC B2961

Circuit Description

The body control module (BCM) monitors the ignition key alarm switch. When the key is in the ignition, the ignition key alarm switch is closed and the signal circuit is low. When the key is not in the ignition, the ignition key alarm switch is open and the signal circuit is high.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B2961 Key In Ignition Circuit

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC
    • The ignition 1 voltage circuit is active and the key in ignition switch signal circuit is inactive and the signal circuit is high.
    • The above conditions are present for more than 5 seconds.

Action Taken When the DTC Sets

The BCM stores DTC B2961 in memory.

Conditions for Clearing the DTC
    • The DTC becomes history when the fault is no longer present.
    • A history DTC is cleared after 100 consecutive ignition cycles, if the condition for the malfunction is no longer present.
    • The BCM receives the clear code command from the scan tool.

Step

Action

Yes

No

Schematic Reference: Audible Warnings Schematics

Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views or Body Control System Schematics

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With the scan tool, observe the Key In Ignition parameter in the body control module (BCM) data list.

Does the Key In Ignition parameter display Yes?

Go to Step 3

Go to Step 4

3
  1. Turn OFF the ignition.
  2. Remove the key.
  3. Disconnect the BCM connector C4.
  4. Connect a test lamp between the ignition 1 voltage circuit and a good ground.

Does test lamp illuminate?

Go to Step 7

Go to Step 11

4
  1. Turn OFF the ignition.
  2. Disconnect the BCM connector C4.
  3. Connect a test lamp between the signal circuit of the ignition key alarm switch and battery positive voltage.
  4. Turn ON the ignition, with the engine OFF.

Does the test lamp illuminate?

Go to Step 8

Go to Step 5

5

Test the signal circuit of the ignition key alarm switch for an open or for a high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 6

6

Test the ground circuit of the ignition key alarm switch for an open or for a high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 9

7

Test the ignition 1 voltage circuit for a short to battery voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 11

8

Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 11

9

Inspect for poor connections at the harness connector of the ignition switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 10

10

Replace the ignition switch. Refer to Ignition and Start Switch Replacement .

Did you complete the replacement?

Go to Step 12

--

11

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 12

--

12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC set?

Go to Step 2

System OK