The Time Sert® thread repair process involves a solid bushing type insert. The insert is made of carbon and is self-locking. During the bushing installation process, the driver tool expands the bottom external threads of the insert into the base material. This action mechanically locks the insert in place. Also when installed to the proper depth, the flange of the insert will be seated against the counter-bore of the repaired hole.

Caution: Protect yourself by wearing safety glasses, earplugs, a respirator, gloves, and safety shoes while performing work on the vehicle.

Important: The use of a cutting type fluid GM P/N 1052864, WD 40®, or equivalent is recommended when performing drilling, counter-boring, and tapping procedures.

Driver oil must be used on installer driver tool.

The tool kits are designed for use with either a suitable tap wrench or drill motor.

1. Drill out threads of damaged hole.

•	M6 inserts require a minimum drill depth of 15 mm (0.59 in).

•	M8 inserts require a minimum drill depth of 20 mm (0.79 in).

•	M10 inserts require a minimum drill depth of 23.5 mm (0.93 in).

2. Using compressed air, clean out any chips.



3. Counter-bore hole to full depth permitted by tool.
4. Using compressed air, clean out any chips.



5. Using a tap wrench, tap threads of drilled hole.

•	M6 inserts require a minimum tap depth of 15 mm (0.59 in).

•	M8 inserts require a minimum tap depth of 20 mm (0.79 in).

•	M10 inserts require a minimum tap depth of 23.5 mm (0.93 in).

Using compressed air, clean out any chips.

7. Spray cleaner GM P/N 12346139, P/N 12377981 or equivalent into holes.
8. Using compressed air, clean any cutting oil and chips out of drilled hole.




Important: Do not allow oil or other foreign material to contact outside diameter (OD) of insert.

9. Lubricate threads of installer tool with drive oil.



10. Install insert onto installer tool.



11. Apply High Strength Threadlock Red, J42385-109 or equivalent to insert OD threads.




Important: Installer tool will tighten up before screwing completely through insert. This is acceptable. You are forming bottom threads of insert and mechanically locking insert to base material threads.

12. Install insert into hole.

12.1.

Install insert until flange of insert contacts counter-bored surface.

12.2.

Continue to rotate installer tool through insert.





Important: A properly installed insert will be either flush or slightly below flush with surface of base material.

13. Inspect insert for proper installation into hole.

1. The main cap bolt thread repair kit consists of the following items:

•

Drill

•

Tap

•

Installer

•	Fixture Plate

•	Long Bolts

•	Short Bolts

•	Alignment Pin

•

Bushing




2. Remove the alignment doll pins on holes 1-4 if necessary.



3. Install fixture plate, bolt and bushing onto engine block.

Position the fixture plate and bushing over the hole that is to be replaced.

4. Position alignment pin in desired hole and tighten fixture retaining bolts.
5. Drill out the damaged hole.
6. Using compressed air, clean out any chips.



7. Using a tap wrench, tap the threads of the drilled hole.

In order to tap new threads to the proper depth, rotate the tap into the hole until the mark (3) on the tap aligns with the top of the bushing.

8. Using compressed air, clean out any chips.
9. Spray cleaner GM P/N 12346139 (or equivalent) into the hole.
10. Using compressed air, clean any cutting oil and chips out of the hole.




Important: Do not allow oil or other foreign material to contact the outside diameter (OD) of the insert.

11. Lubricate the threads of the installer tool (2) with the driver oil (1).



12. Install the insert (2) onto the driver tool (1).



13. Apply High Strength Threadlocker® Red, J42385-109, (or equivalent) to the insert OD threads.




Important: The fixture plate and bushing remains installed onto the engine block during the insert installation procedure.

14. Install the insert and driver through the bushing (2), fixture plate (1) and into the hole.

Rotate the driver tool until the mark on the tool (3) aligns with the top of the bushing (2).

The installer tool will tighten up before screwing completely through the insert. This is acceptable. You are forming the bottom threads of the insert and mechanically locking the insert to the base material threads.

15. Remove the driver, bushing (2), fixture plate (1) and bolts.



16. Install the alignment doll pins in holes 1-4 if necessary.

The cylinder head bolt thread repair kit consists of the following items:

1. Drill
2. Tap
3. Installer
4. Alignment Pin
5. Bushing
6. Bolts
7. Fixture Plate

Caution: Protect yourself by wearing safety glasses, earplugs, a respirator, gloves, and safety shoes while performing work on the vehicle.

Important: The use of a cutting type fluid GM P/N 1052864, WD 40® (or equivalent) is recommended when performing drilling, counter-boring, and tapping procedures.

Driver oil must be used on installer driver tool.

The tool kits are designed for use with either a suitable tap wrench or drill motor.

1. Install fixture plate, bolts, and bushing onto engine block deck.
2. Position fixture plate and bushing over hole that is to be repaired.



3. Position alignment pin through bushing and into hole.
4. With alignment pin in desired hole, tighten fixture retaining bolts.
5. Remove alignment pin from hole.




Important: During drilling process, it is necessary to repeatedly remove drill and clean chips from hole.

6. Install drill sleeve onto the drill if required.
7. Drill out threads of damaged hole.
8. Using compressed air, clean out any chips.

•	M6 inserts require a minimum drill depth of 15 mm (0.59 in).

•	M8 inserts require a minimum drill depth of 20 mm (0.79 in).

•	M10 inserts require a minimum drill depth of 23.5 mm (0.93 in).




9. Using tap wrench, tap threads of drilled hole.



10. Tap new threads to proper depth by turning tap into hole until mark on tap aligns with top of drill bushing.
11. Remove fixture plate, bushing, and bolts.
12. Using compressed air, clean out any chips.
13. Spray cleaner GM P/N 12346139, P/N 12377981 (or equivalent) into hole.
14. Using compressed air, clean any cutting oil and chips out of hole.




Important: Do not allow oil or other foreign material to contact outside diameter (OD) of insert.

15. Lubricate threads of installer tool with driver oil.



16. Install the insert (2) onto driver tool (1).



17. Apply High Strength Threadlock Red, J42385-109 (or equivalent) to insert OD threads.



18. Install insert and driver into hole.

Important: Installer tool will tighten up before screwing completely through insert. This is acceptable. You are forming bottom threads of insert and mechanically locking insert to base material threads.

19. Rotate driver tool until mark on tool aligns with deck surface of engine block.