GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 38188 Cylinder Head Broken Bolt Extractor Kit


    Object Number: 747114  Size: SH
  1. Remove the EGR cover (2), the bolts (1), and the EGR cover gasket (3).

  2. Object Number: 465863  Size: SH
  3. Remove the cylinder head to the block bolts in sequence.
  4. Discard the bolts.


    Object Number: 412427  Size: SH
  5. Remove the cylinder head.
  6. Remove the cylinder head gasket.
  7. Clean all of the gasket surfaces.
  8. Use the following procedures when cleaning the cylinder head and cylinder block surfaces:
  9. •  Use a razor blade gasket scraper to clean the cylinder head and cylinder block gasket surfaces. Do not scratch or gouge any surface.

       Important: Do not use any other method or technique to clean these gasket surfaces.

    • Use a new razor blade for each cylinder head and cylinder block.

       Important: Be careful not to gouge or scratch the gasket surfaces. Do not gouge or scrape the combustion chamber surfaces. The feel of the gasket surface is important, not the appearance. There will be indentations from the gasket left in the cylinder head after all of the gasket material is removed. These small indentations will be filled in by the new gasket.

    • Hold the razor blade as parallel to the gasket surface as possible.

    Important: Do not use a tap to clean the cylinder head bolt holes.

  10. Clean the old sealer/lube and dirt from the bolt holes.
  11. Clean the bolt holes with a nylon bristle brush.
  12. Caution: Wear safety glasses to avoid injury when using compressed air or any cleaning solvent. Bodily injury may occur if fumes are inhaled or if skin is exposed to chemicals.

  13. When cleaning the cylinder head bolt holes use a suitable commercial spray liquid solvent and compressed air from an extended-tip blow gun to reach the bottom of the holes.
  14. Remove any broken long cylinder head bolts using the J 38188 .

Tools Required

J 38188 Cylinder Head Broken Bolt Extractor Kit

Removal Procedure


    Object Number: 897659  Size: SH
  1. Remove the EGR cover, bolts, and EGR cover gasket.

  2. Object Number: 895538  Size: SH
  3. Remove the cylinder head to block bolts using the loosening sequence. Discard the used bolts.

  4. Object Number: 895550  Size: SH
  5. Remove the cylinder head.
  6. Remove the cylinder head gasket.
  7. Clean all gasket surfaces.
  8. Use the following procedures when cleaning the cylinder head and cylinder block surfaces:
  9. • Use a razor blade gasket scraper to clean the cylinder head and cylinder block gasket surfaces. Do not scratch or gouge any surface.

       Important: Do not use any other method or technique to clean these gasket surfaces.

    • Use a new razor blade for each cylinder head and cylinder block.

       Important: Be careful not to gouge or scratch the gasket surfaces. Do not gouge or scrape the combustion chamber surfaces. The feel of the gasket surface is important, not the appearance. There will be indentations from the gasket left in the cylinder head after all the gasket material is removed. These small indentations will be filled in by the new gasket.

    • Hold the razor blade as parallel to the gasket surface as possible.

    Important: Do not use a tap to clean the cylinder head bolt holes. Use a nylon bristle brush.

  10. Clean the old sealer/lube and dirt from bolts, studs, and cylinder head bolt holes.
  11. Clean the bolt holes with a nylon bristle brush.
  12. Caution: Wear safety glasses to avoid injury when using compressed air or any cleaning solvent. Bodily injury may occur if fumes are inhaled or if skin is exposed to chemicals.

  13. When cleaning the cylinder head bolt holes use a suitable commercial spray liquid solvent and compressed air from an extended-tip blow gun to reach the bottom of the holes.
  14. Remove any broken long cylinder head bolts using the J 38188 .