Circuit Description
The accelerator pedal position (APP) sensor is made up of two sensors that are housed inside one assembly. The engine control module (ECM) supplies a separate 5-volt reference and low reference circuit for each of the sensors. The 5-volt reference for the APP sensor 2 is supplied from the same source in the ECM as the 5-volt reference for the throttle position sensors. The 5-volt reference voltage for all of the sensors is supplied on separate ECM terminals, but the terminals are connected internally to a voltage supply. The APP sensor 2 sends a signal indicating the accelerator pedal position and the ECM actuates the throttle plates based on this information. The APP sensor 2 signal voltage increases as the pedal is applied. If the ECM detects that the signal voltage is more than 2.41 volts, DTC P2128 will set.
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The battery voltage is more than 10 volts. |
| • | The accelerator pedal is not in the rest position. |
Conditions for Setting the DTC
The APP sensor 2 voltage is more than 2.41 volts for more than 140 milliseconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 |
Is the APP sensor 2 voltage more than the specified value? | 4.6 V | Go to Step 3 | Go to Step 4 |
3 |
Is the APP sensor 2 voltage less than the specified value? | 0.02 V | Go to Step 6 | Go to Step 13 |
4 |
Does the DTC fail this ignition? | -- | Go to Step 6 | Go to Step 5 |
5 |
Did the DTC fail this ignition? | -- | Go to Step 19 | Go to Intermittent Conditions |
6 |
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 7 | Go to Step 11 |
7 |
Is the APP sensor 2 voltage within the specified value? | 4.8-5.2 V | Go to Step 8 | Go to Step 13 |
8 |
Is the resistance less than the specified value? | 5 ohms | Go to Step 16 | Go to Step 9 |
9 | Test the low reference circuit of the APP sensor 2 for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 10 |
10 | Measure the resistance from the case of the ECM to the battery ground. Is the resistance less than the specified value? | 5 ohms | Go to Step 17 | Go to Step 15 |
11 |
Is the voltage within the specified range after disconnecting any component? | 4.8-5.2 V | Go to Step 18 | Go to Step 12 |
12 | Test the 5-volt reference circuit of the APP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 14 |
13 | Test the signal circuit of the APP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 17 |
14 | Test the 5-volt reference circuits of the throttle position (TP) sensors for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 17 |
15 | Repair the open or high resistance in the ECM ground circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 21 | -- |
16 | Test for an intermittent and for a poor connection at the APP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 19 |
17 | Test for an intermittent and for a poor connection at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 20 |
18 | Replace the component that, when disconnected, caused the voltage to return to the specified value. Refer to the appropriate replacement procedure. Did you complete the replacement? | -- | Go to Step 21 | -- |
19 | Replace the accelerator pedal assembly. Refer to Accelerator Pedal Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 21 | -- |
20 | Replace the ECM. Refer to Engine Control Module Replacement . Did you complete the replacement? | -- | Go to Step 21 | -- |
21 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 22 |
22 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
