GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2004 🢒 L300/LW300 🢒 DTC 🢒 DTC P0757

DTC P0757 2.2L


Object Number: 40582 Size: SF
Master Electrical Component List
Automatic Transmission Controls Schematics 2.2 L
OBD II Symbol Description Notice

Circuit Description

The 2-3 shift solenoid (SS) valve is a normally-open exhaust valve that, in conjunction with the 1-2 shift solenoid (SS) valve, allows 4 different shifting combinations. Refer to Shift Solenoid Valve State and Gear Ratio . The 2-3 SS valve is attached to the control valve body within the transmission.

The PCM monitors the actual gear ratio, and compares the actual gear ratio with the commanded gear ratio. DTC P0757 sets under 2 conditions:

    • A stuck OFF 2-3 SS valve
    • A stuck OFF 2-3 shift valve

When the PCM detects a 1-2-2-1 shift pattern, then DTC P0757 sets. DTC P0757 is a type A DTC.

Conditions for Running the DTC
    • No MAP DTCs P0107 or P0108.
    • No TP DTCs P0121, P0122 or P0123.
    • No VSS DTCs P0502 or P0503.
    • No ISS DTCs P0716 or P0717.
    • No TCC stuck ON DTC P0742.
    • No shift solenoid electrical DTCs P0753 or P0758.
    • No TCC electrical DTC P1860.
    • The transmission fluid temperature is 20-130°C (68-266°F).
    • The TP is greater than 8 percent.
    • The input speed is 150-6,000 RPM.
    • The output speed is greater than 150 RPM.
    • The engine torque is greater than 27 N·m (20 lb ft) when 3rd gear is commanded.
    • The time since the last gear change is greater than 0.20 seconds.

Conditions for Setting the DTC
    • The PCM commands 3rd gear and the gear ratio is 1.54:1-1.71:1, 2nd gear, for 3 seconds.
    • The PCM commands 4th gear and the gear ratio is 2.87:1-3.13:1, 1st gear, for 2 seconds.

Action Taken When the DTC Sets
    • The PCM illuminates the malfunction indicator lamp (MIL).
    • The PCM commands maximum line pressure.
    • The PCM inhibits TCC engagement.
    • The PCM inhibits 4th gear when in HOT mode.
    • The PCM freezes transmission adaptive functions.
    • The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
    • The PCM stores DTC P0757 in PCM history.

Conditions for Clearing the MIL/DTC
    • The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
    • A scan tool can clear the MIL/DTC.
    • The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    • The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    • If you clear DTC P0757, and then cannot set DTC P0757 again, inspect for the following conditions:
       - Fluid contamination
       - Plugged fluid circuits
       - Restricted fluid circuits
    • Refer to Shift Solenoid Valve State and Gear Ratio .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step verifies a 1-2-2-1 shift pattern.

    2.

  2. This step tests for a mechanical or hydraulic condition causing the 2-3 SS valve to be stuck OFF, or the circuit to be applied.

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 2.2L (L61)

2

Did you perform the Transmission Fluid Checking Procedure?

--

Go to Step 3

Go to Transmission Fluid Check

3
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.

    3. Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.

  3. Record the DTC Freeze Frame and Failure Records.
  4. Clear the DTC.
  5. Use the scan tool snapshot mode in order to record current gear and gear ratio.
  6. Drive the vehicle in D4, in order to obtain a 1-2, 2-3 and 3-4 shifts with a TP greater than 8%.

Are current gear and gear ratio within the specified values?

1st/4th:

2.87:1-3.13:1

2nd/3rd:

1.54:1-1.71:1

Go to Step 4

Go to Diagnostic Aids

4
  1. Inspect the 2-3 shift circuit for the following conditions:
    2. • 2-3 SS valve mechanically stuck OFF
    • 2-3 shift valve stuck in the released position
    • Refer to Shift Solenoid Leak Test .
    • Damaged 2-3 SS valve O-ring
  2. Repair the circuit as necessary.

Refer to 2-3 Shift Solenoid Valve Replacement .

Did you complete the repair?

--

Go to Step 5

--

5

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    4. • Drive the vehicle in D4 with the TP greater than 8 percent and the engine torque greater than 27 N·m (20 lb ft).
    • Allow the transmission to shift through all the gears.
    • Monitor the current gear and gear ratios. The actual gear ratios must match the commanded gears for 1 second, for all gears.
  4. Select Specific DTC.
  5. Enter DTC P0757.

Has the test run and passed?

--

Go to Step 6

Go to Step 2

6

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 2.2L (L61)

System OK

DTC P0757 3.0L


Object Number: 40582 Size: SF
Master Electrical Component List
Automatic Transmission Controls Schematics 3.0 L
OBD II Symbol Description Notice

Circuit Description

The 2-3 shift solenoid (SS) valve is a normally-open exhaust valve that, in conjunction with the 1-2 shift solenoid (SS) valve, allows 4 different shifting combinations. Refer to Shift Solenoid Valve State and Gear Ratio . The 2-3 SS valve is attached to the control valve body within the transmission.

The TCM monitors the actual gear ratio, and compares the actual gear ratio with the commanded gear ratio. DTC P0757 sets under 2 conditions:

    • A stuck OFF 2-3 SS valve
    • A stuck OFF 2-3 shift valve

When the TCM detects a 1-2-2-1 shift pattern, then DTC P0757 sets. DTC P0757 is a type A DTC.

Conditions for Running the DTC
    • No MAF DTCs P0101, P0102, or P0103.
    • No MAP DTCs P0107 or P0108.
    • No TP DTCs P0121, P0122 or P0123.
    • No VSS DTCs P0502 or P0503.
    • No ISS DTCs P0716 or P0717.
    • No shift solenoid electrical DTCs P1842, P1843, P1845, or P1847.
    • The engine run time is greater than 5 seconds.
    • The transmission fluid temperature is 20-130°C (68-266°F).
    • The TP is greater than 8 percent.
    • The engine torque is greater than 30 N·m (22 lb ft) when 3rd gear is commanded.
    • The vehicle speed is greater than 8 km/h (5 mph).

Conditions for Setting the DTC
    • The TCM commands 3rd gear and the gear ratio is 1.54:1-1.71:1, 2nd gear, for 3 seconds.
    • The TCM commands 4th gear and the gear ratio is 2.87:1-3.13:1, 1st gear, for 2 seconds.

Action Taken When the DTC Sets
    • The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL).
    • The TCM commands maximum line pressure.
    • The TCM inhibits TCC engagement.
    • The TCM inhibits 4th gear.
    • The TCM turns off power to all solenoids.
    • The TCM freezes transmission adaptive functions.
    • The ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as Freeze Frame and Failure Records.
    • The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records.
    • The TCM stores DTC P0757 in TCM history.

Conditions for Clearing the MIL/DTC
    • The ECM turns OFF the MIL after the third consecutive drive trip in which the TCM does not send a MIL illumination request.
    • A scan tool can clear the MIL/DTC.
    • The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    • The TCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the TCM.

Diagnostic Aids
    • If you clear DTC P0757, and then cannot set DTC P0757 again, inspect for the following conditions:
       - Fluid contamination
       - Plugged fluid circuits
       - Restricted fluid circuits
    • Refer to Shift Solenoid Valve State and Gear Ratio .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step verifies a 1-2-2-1 shift pattern.

    2.

  2. This step tests for a mechanical or hydraulic condition causing the 2-3 SS valve to be stuck OFF, or the circuit to be applied.

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 3.0L (L81)

2

Did you perform the Transmission Fluid Checking Procedure?

--

Go to Step 3

Go to Transmission Fluid Check

3
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.

    3. Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from both the ECM and the TCM.

  3. Record the DTC Freeze Frame and Failure Records.
  4. Clear the DTC.
  5. Use the scan tool snapshot mode in order to record current gear and gear ratio.
  6. Drive the vehicle in D4, in order to obtain a 1-2, 2-3 and 3-4 shifts with a TP greater than 8%.

Are current gear and gear ratio within the specified values?

1st/4th:

2.87:1-3.13:1

2nd/3rd:

1.54:1-1.71:1

Go to Step 4

Go to Diagnostic Aids

4
  1. Inspect the 2-3 shift circuit for the following conditions:
    2. • 2-3 SS valve mechanically stuck OFF
    • 2-3 shift valve stuck in the released position
    • Refer to Shift Solenoid Leak Test .
    • Damaged 2-3 SS valve O-ring
  2. Repair the circuit as necessary.

Refer to 2-3 Shift Solenoid Valve Replacement .

Did you complete the repair?

--

Go to Step 5

--

5

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    4. • Drive the vehicle in D4.
    • Allow the transmission to shift through all the gears.
    • Monitor the current gear and gear ratios. The actual gear ratios must match the commanded gears for 1 second, for all gears.
  4. Select Specific DTC.
  5. Enter DTC P0757.

Has the test run and passed?

--

Go to Step 6

Go to Step 2

6

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 3.0L (L81)

System OK