Diagnostic Instructions

DTC Descriptors

DTC P0340: Intake Camshaft Position (CMP) Sensor Circuit Bank 1

DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0345: Intake Camshaft Position (CMP) Sensor Circuit Bank 2

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit Bank 1

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0390: Exhaust Camshaft Position (CMP) Sensor Circuit Bank 2

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
5-Volt Reference Circuit	P0641, P0452, P0107, P0532, P0522	P0340, P0345, P0365, P0390	P0641	--
CMP Sensor Signal Circuit	P0340, P0345, P0365, P0390	P0340, P0345, P0365, P0390	P0340, P0345, P0365, P0390	P0341, P0346, P0366, P0391
Low Reference Circuit	--	P0340, P0345, P0365, P0390	P0340, P0345, P0365, P0390	--

Typical Scan Tool Data

CMP Sensor

Circuit	Short to Ground	Open	Short to Voltage
Operating Conditions: Engine Running Parameter Normal Range: 400-6400 RPM. CMP Sensor parameter should match engine speed parameter
5-Volt Reference Circuit	0 RPM	0 RPM	0 RPM
CKP Sensor Signal Circuit	0 RPM	0 RPM	0 RPM
Low Reference Circuit	Same as Engine Speed	0 RPM	0 RPM

Circuit/System Description

The 4X camshaft position (CMP) sensor circuits consist of an engine control module (ECM) supplied 5-volt reference circuit, low reference circuit, and an output signal circuit. The CMP sensor is an internally magnetic biased digital output integrated circuit sensing device. The sensor detects magnetic flux changes of the teeth and slots of a 4-tooth reluctor wheel attached to the camshaft. As each reluctor wheel tooth rotates past the CMP sensor, the resulting change in the magnetic field is used by the sensor electronics to produce a digital output pulse. The sensor returns a digital ON/OFF DC voltage pulse of varying frequency, with 4 varying width output pulses per camshaft revolution that represent an image of the camshaft reluctor wheel. The frequency of the CMP sensor output depends on the velocity of the camshaft. The ECM decodes the narrow and wide tooth pattern to identify camshaft position. This information is then used to determine the optimum ignition and injection points of the engine. The ECM also uses CMP sensor output information to determine the camshaft relative position to the crankshaft, to control camshaft phasing, and for limp-home operation.

Conditions for Running the DTC

Conditions for Setting the DTC

Important: The ECM detects engine movement by sensing the airflow through the mass air flow (MAF) sensor is more than 3 g/s, or by sensing crankshaft position (CKP) sensor pulses.

P0340, P0345, P0365, or P0390

P0341, P0346, P0366, or P0391

Action Taken When the DTC Sets

Conditions for Clearing the MIL/DTC

Diagnostic Aids

With a DTC set, the engine may crank for an extended period of time at start-up

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Description and Operation

Electronic Ignition (EI) System Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Circuit/System Verification

1. With the ignition OFF, inspect the engine wiring harnesses carrying the CMP sensor circuits for the following conditions:

•	Close routing of secondary ignition wires

•	Close routing of aftermarket electrical equipment

•	Close to solenoids, motors, and relays

⇒	Correct any wire harness routing or component placement conditions if it is determined to be a possible source of electrical interference.

2. Start the engine. Using the Live Plot function on the scan tool, select the CMP parameter. Change the minimum spec to 400 RPM and the maximum spec to 4,000 RPM. Select the CKP sensor parameter. Change the minimum spec to 600 RPM and the maximum spec to 3,300 RPM.
3. Observe the scan tool.
4. Quickly accelerate and release the accelerator pedal several times. Do not exceed 3,200 RPM. The graphed lines on the Live Plot display should track together across the screen.

⇒	If the vehicle passes the Circuit/System Verification Test, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

Circuit/System Testing

P0340, P0345, P0365, or P0390

1. Ignition OFF, disconnect the affected CMP sensor connector.
2. Test for less than 1 ohm of resistance between ECM side of the low reference circuit and ground.

⇒	If greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, test for 4.8-5.2 volts between the ECM side of the 5-volt reference circuit and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Ignition ON, test for 4.8-5.2 volts between the signal circuit and ground.

⇒	If less than the specified range, test the affected signal circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the affected signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Ignition ON, using a jumper wire connected to ground, momentarily touch the CMP sensor signal circuit repeatedly. The applicable CMP active counter parameter should increment.

⇒	If the CMP active counter does not increment, replace the ECM.

⇒	If the circuits test normal, replace the CMP sensor.

P0341, P0346, P0366, or P0391

1. Ignition OFF, inspect the CMP sensor for looseness and correct installation.

⇒	If the sensor is loose, inspect the sensor and the O-ring for damage. Replace as necessary.

2. Inspect the engine for the following conditions:

•	Engine oil for debris

•	Camshaft reluctor wheel for damage

•	The timing chain, tensioner, and sprockets for wear or damage

⇒	If debris is found in the engine oil, inspect the internal engine components to determine the cause. Repair or replace any worn or damaged components. Refer to Camshaft Timing Drive Components Cleaning and Inspection and Camshaft Cleaning and Inspection .

Component Test

Important: You must perform the Circuit/System Testing before proceeding with Component Testing.

1. Inspect the CMP sensor for looseness and correct installation. Remove the CMP sensor from the engine and inspect the sensor and the O-ring for damage.

⇒	If the sensor is loose, incorrectly installed, or damaged, repair or replace the CMP sensor.

2. Connect the CMP sensor connector to the CMP sensor. Turn ON the ignition, with the engine OFF.
3. Ignition ON and engine OFF. Observe the applicable CMP Active Counter parameter on the scan tool. Pass a steel object by the tip of the sensor repeatedly. The CMP Active Counter parameter should increment.

⇒	If the parameter does not increment, replace the CMP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.