DTC P0563 ECM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563: System Voltage High - ECMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur if the voltage is out of range.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The ECM detects that the battery voltage is greater than 18 V for 5 seconds.
Action Taken When the DTC Sets
DTC P0563 is a type C DTC.
Conditions for Clearing the DTC
DTC P0563 is a type C DTC.
Diagnostic Aids
| • | This DTC could be set by overcharging with a battery charger or jump starting. |
| • | A high voltage value in multiple modules indicates a concern in the charging system. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- If all circuits test normal, replace the ECM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References - for ECM replacement, setup, and programming.
DTC P0563 FPCM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563: System Voltage High - FPCMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Ignition ON, engine OFF. Parameter Normal Value: 12.6 Volts | |||
B+ | 0.0 Volts | 0.0 Volts | 12.6 Volts |
Circuit/System Description
The fuel pump control module (FPCM) monitors the battery voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The FPCM detects that the battery voltage is greater than 16 V.
Action Taken When the DTC Sets
DTC P0563 is a type C DTC.
Conditions for Clearing the DTC
DTC P0563 is a type C DTC.
Diagnostic Aids
| • | Some possible causes of this DTC are overcharging with a battery charger and jump starting. |
| • | A high voltage value in multiple modules indicates a concern in the charging system. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- Observe the scan tool Ignition 1 Signal parameter. The reading should be between 12.6 and 15.0 V.
| ⇒ | If not within the specified range, refer to Charging System Test. |
| ⇒ | If greater than the specified range, replace the FPCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References - for FPCM replacement, setup, and programming.
