Liftgate Emblem/Nameplate Replacement. Saturn OUTLOOK

For 1990-2009 cars only

Makes 🢒 Saturn 🢒 2007 🢒 OUTLOOK - FWD 🢒 Body Hardware and Trim 🢒 Exterior Trim 🢒 Liftgate Emblem/Nameplate Replacement

Liftgate Emblem/Nameplate Replacement Outlook

Callout	Component Name
1	Outlook Emblem / Nameplate Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the liftgate. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Callout

Component Name

Outlook Emblem / Nameplate

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the liftgate.
Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Callout	Component Name
1	Outlook Emblem / Nameplate Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the liftgate. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Callout

Component Name

Outlook Emblem / Nameplate

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the liftgate.
Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Callout	Component Name
1	Outlook Emblem / Nameplate Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section. Procedure The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Close the liftgate. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Callout

Component Name

Outlook Emblem / Nameplate

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Close the liftgate.
Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.