GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The driver side deployment loop consists of the following components:

    • An inflatable restraint side impact module LR
    • The side impact module LR high circuits
    • The side impact module LR low circuits

A shorting bar is used within the side impact module LR connector. The shorting bar will short together the side impact module LR high circuit and the side impact module LR low circuit when the connector is disconnected. This helps prevent unwanted deployment of the inflator module during servicing. During a side or frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop. This flow of current will deploy the side impact module LR. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.

DTC Descriptors

This diagnostic procedure supports the following DTCs:

    • DTC B0109 Left Rear Side Deployment Loop Resistance Low
    • DTC B0110 Left Rear Side Deployment Loop Open
    • DTC B0111 Left Rear Side Deployment Loop Voltage Out of Range

Conditions for Running the DTC

Ignition 1 voltage is within the normal operating voltage range.

Conditions for Setting the DTC

    • DTC B0109 will set when the SDM detects the LR side impact module deployment loop resistance is less than 1.3 ohms for 500 milliseconds.
    • DTC B0110 will set when one of the following conditions occurs:
       - The SDM detects the LR side impact module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
       - The SDM detects the voltage at the LR side impact module high control is less than 2.4 volts and LR side impact module deployment loop resistance is 6 ohms or greater for 500 milliseconds.
    • DTC B0111 will set when one of the following conditions occurs:
       - The SDM detects the voltage at the LR side impact module high control is greater than 6 volts for 500 milliseconds.
       - The SDM detects the voltage at the LR side impact module high control is less than 2.4 volts and the LR side impact module deployment loop resistance is less than 6 ohms for 500 milliseconds.

Action Taken When the DTC Sets

The SDM commands ON the AIR BAG indicator via class 2 serial data.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    • You issue a scan tool CLEAR DTCs command.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Diagnostic Aids

The following are possible causes of the malfunction:

    • A short between the side impact module LR high and low circuits
    • An open or a high resistance in the side impact module LR high or low circuits
    • A short to ground or a short to voltage in the side impact module LR high or low circuits
    • The side impact module LR connector
    • The SDM connector
    • A malfunctioning side impact module LR
    • A malfunctioning SDM

Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step tests to see what DTCs are present. If DTC B0109 is present, test the side impact module LR for a short between high and low circuits. If DTC B0110 is present, test the side impact module LR high and low circuits for an open and for high resistance. If DTC B0111 is present, test the side impact module LR high and low circuits for a short to ground or a short to voltage.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Turn OFF the ignition.
  2. Disconnect the LR side impact module in-line connector. Refer to Rear Seat Body Side Inflatable Restraint Module Replacement .
  3. Inspect the component and harness sides of the in-line connector for the side impact module LR for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Does connector exhibits any signs of damage or corrosion?

Go to Step 3

Go to Step 4

3

  1. If the LR side impact module harness connector exhibits any of the above conditions, replace the side impact module wiring harness. Refer to Rear Seat Body Side Inflatable Restraint Module Replacement .
  2. Replace the harness side of the LR side impact module in-line connector. Refer to Connector Repairs .

Did you complete the replacement?

Go to Step 9

--

4

    Important: If the scan tool displays multiple codes, diagnose the open code first.

  1. Install the J 38715-A Driver and Passenger SIR Load Tool or SA9409Z-A to the harness side of the side impact module LR in-line connector. Use the PASSENGER INFLATOR connector.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, request the SIR DTC display.

Does the scan tool indicate that either DTC B0109, B0110, or B0111 is current?

Go to Step 5

Go to Step 7

5

  1. Turn OFF the ignition.
  2. Remove the J 38715-A or SA9409Z-A.
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References for replacement, setup, and programming.
  4. Inspect the SDM connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 6

6

  1. If DTC B0109 is present, test the side impact module LR circuits for a short between the high and low circuits.
  2. If DTC B0110 is present, test the side impact module LR high and low circuits for an open and for high resistance.
  3. If DTC B0111 is present, test the side impact module LR high and low circuits for a short to ground and for a short to voltage.
  4. All the above conditions refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

  1. Turn OFF the ignition.
  2. Replace the side impact module LR. Refer to Rear Seat Body Side Inflatable Restraint Module Replacement .

Did you complete the replacement?

Go to Step 9

--

8

  1. Turn OFF the ignition.
  2. Replace the SDM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 9

--

9

  1. Reconnect all SIR System components.
  2. Verify that all components, connectors, and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK