DTC P1640 and/or P1641 QDM Module A
Circuit Description
A quad driver module (QDM) is an electronic switch which completes a ground
circuit when switched ON. The QDM independently controls 4 separate outputs.
A load is connected between battery voltage and the QDM, allowing the QDM driver to
control the output. Each QDM has fault detection logic which compares QDM driver input
and output voltages. The logic expects to measure less than 3 volts when the
QDM driver is ON and greater than 7 volts when OFF. The QDM has
only 1 fault line that will detect a fault on any of the 4 outputs.
The scan tool can be used to cycle the outputs ON or OFF. The scan tool can also perform
an automated test which can isolate the faulty circuit.
Conditions for Setting the DTC
Important: The QDM circuit is continuously checked when
the engine is running.
DTC P1640 and/or P1641 will set if:
| • | There is an open, short to ground, or short to voltage on any of the QDM
output circuits. |
| • | SERVICE telltale lamp circuit |
| • | Low coolant/hot telltale lamp circuit |
| • | A fault is detected for 5 seconds for DTC P1641. |
| • | A fault is detected for 20 seconds for DTC P1640. |
Diagnostic Aids
| • | If 1 output is faulty, the PCM will shut down only that QDM output
and not the entire quad driver unless the quad driver reaches its thermal limit, short
to voltage. At this time it will turn all 4 quad driver outputs OFF. When the
quad driver cools down it will turn back ON and this process will start over. |
| • | A shorted or open circuit or bulb can cause a DTC P1640 and/or
P1641 to set. |
Use the scan tool to diagnose the quad driver circuits and perform an off-board
QDM test.
When viewing QDM fault, using a scan tool dynamic display or MIL telltale, you
may notice the fault appears to be intermittent. This may be due to an intermittent
fault, but more likely it is due to the way the fault detection works.
For example, if the SERVICE telltale lamp is OFF, the PCM expects to refer to
12 volts on the circuit. If the circuit is open, 0 volts will be measured
on the circuit and the fault will be displayed. However, if the lamp is turned ON,
the PCM expects to measure 0 volts on the circuit and will not detect a fault.
This causes an intermittent problem because the lamp is not continuously ON.
DTC P1640 and/or P1641 QDM Module A - Service Lamp
Circuit Description
A quad driver module (QDM) is an electronic switch which completes a ground
circuit when switched ON. The QDM independently controls 4 separate outputs.
A load is connected between battery voltage and the QDM allowing the QDM driver to
control the output. Each QDM has fault detection logic which compares QDM driver input
and output voltages. The logic expects to measure less than 3 volts when the
QDM driver is ON and greater than 7 volts when OFF. The QDM has only 1 fault
line that will detect a fault on any of the 4 outputs. The scan tool can be
used to cycle the outputs ON or OFF. The scan tool can also perform an automated test
which can isolate the faulty circuit.
Conditions for Setting the DTC
Important: The QDM circuit is continuously checked when
the engine is running.
DTC P1640 and/or P1641 will set if:
| • | There is an open, short to ground, or short to voltage in the QDM output
SERVICE telltale lamp circuit. |
| • | A fault is detected for 5 seconds for DTC P1641. |
| • | A fault is detected for 20 seconds for DTC P1640. |
Diagnostic Aids
| • | If 1 output is faulty, the PCM will shut down only that QDM output
and not the entire quad driver unless the quad driver reaches its thermal limit, short
to voltage. At this time it will turn all 4 quad drivers outputs OFF. When
the quad driver cools down, it will turn back ON and this process will start over. |
| • | A shorted or open circuit or bulb can cause a code to set. |
| • | Check the 10 amp IGN 1 fuse in the IPJB. |
Use the Saturn service stall system, if available, to diagnose the quad driver
circuits or use a scan tool and perform an off-board QDM test.
When viewing a QDM fault, using a scan tool dynamic display or MIL telltale,
you may notice the fault appears to be intermittent. This may be due to an intermittent
fault, but more likely it is due to the way the fault detection works.
For example, if the SERVICE telltale lamp is OFF, the PCM expects to refer to
12 volts on the circuit line. If the circuit is open, 0 volts will be
measured on the circuit and the fault will be displayed. However, if the lamp is turned
ON, the PCM expects to measure 0 volts on the circuit, and will not detect
a fault. This causes an intermittent problem because the lamp is not continuously
ON.
DTC P1640 and/or P1641 QDM Module A - Low Coolant/Hot Lamp
Circuit Description
A quad driver module (QDM) is an electronic switch which completes a ground
circuit when switched ON. The QDM independently controls 4 separate outputs.
A load is connected between battery voltage and the QDM, allowing the QDM driver to
control the output. Each QDM has fault detection logic which compares QDM driver input
and output voltages. The logic expects to measure less than 3 volts when the
QDM driver is ON and greater than 7 volts when OFF. The QDM has only 1 fault
line that will detect a fault on any of the 4 outputs. The scan tool can be
used to cycle the outputs ON or OFF. The scan tool can also perform an automated test
which can isolate the faulty circuit.
Conditions for Setting the DTC
Important: The QDM circuit is continuously checked when
the engine is running.
DTC P1640 and/or P1641 will set if:
| • | There is an open, short to ground, or short to voltage on the QDM output
low coolant/hot telltale lamp circuit. |
| • | A fault is detected for 5 seconds for DTC P1641. |
| • | A fault is detected for 20 seconds for DTC P1640. |
Diagnostic Aids
| • | If 1 output is faulty, the PCM will shut down only that QDM output
and not the entire quad driver unless the quad driver reaches its thermal limit, short
to voltage. At this time it will turn all 4 quad driver outputs OFF. When the
quad driver cools down it will turn back ON and this process will start over. |
| • | A shorted or open circuit or bulb can cause a DTC to set. |
| • | Check the 10 amp IGN 1 in the IPJB. |
Use the Saturn service stall system, if available, to diagnose the quad driver
circuits or use a scan tool and perform an off-board QDM test.
When viewing QDM fault, using a scan tool dynamic display or MIL telltale, you
may notice the fault appears to be intermittent. This may be due to an intermittent
fault, but more likely it is due to the way the fault detection works.
For example, if the SERVICE telltale lamp is OFF, the PCM expects to refer to
12 volts on the circuit. If the circuit is open, 0 volts will be measured
on the circuit and the fault will be displayed. However, if the lamp is turned ON,
the PCM expects to measure 0 volts on the circuit and will not detect a fault.
This causes an intermittent problem because the lamp is not continuously ON.
DTC P1640 and/or P1641 QDM Module A - Cruise Clutch
Circuit Description
A quad driver module (QDM) is an electronic switch which completes a ground
circuit when switched ON. The QDM independently controls 4 separate outputs.
A load is connected between battery voltage and the QDM, allowing the QDM driver to
control the output. Each QDM has fault detection logic which compares QDM driver input
and output voltages. The logic expects to measure less than 3 volts when the
QDM driver is ON and greater than 7 volts when OFF. The QDM has only 1 fault
line that will detect a fault on any of the 4 outputs. The scan tool can be
used to cycle the outputs ON or OFF. The scan tool can also perform an automated test
which can isolate the faulty circuit.
Conditions for Setting the DTC
Important: The QDM circuit is continuously checked when
the engine is running.
DTC P1640 and/or P1641 will set if:
| • | There is an open, short to ground, or short to voltage on the QDM output
cruise clutch circuit. |
| • | A fault is detected for 5 seconds for DTC P1641. |
| • | A fault is detected for 20 seconds for DTC P1640. |
Diagnostic Aids
| • | If 1 output is faulty, the PCM will shut down only that QDM output
and not the entire quad driver unless the quad driver reaches its thermal limit, short
to voltage. At this time it will turn all 4 quad driver outputs OFF. When the
quad driver cools down it will turn back ON and this process will start over. |
| • | Check the 5 amp cruise fuse in the IPJB. |
Use the Saturn service stall system, if available, to diagnose the quad driver
circuits.
When viewing QDM fault, using a scan tool dynamic display or MIL telltale, you
may notice the fault appears to be intermittent. This may be due to it being an intermittent
fault, but more likely it is due to the way the fault detection logic works.
For example, if the SERVICE telltale lamp is OFF, the PCM expects to refer to
12 volts on the circuit. If the circuit is open, 0 volts will be measured
on the circuit and the fault will be displayed. However, if the lamp is turned ON
due to low coolant conditions, the PCM expects to measure 0 volts on the circuit
and will not detect a fault.
DTC P1640 and/or P1641 QDM Module A - Low Fuel Lamp
Circuit Description
A quad driver module (QDM) is an electronic switch which completes a ground
circuit when switched ON. The QDM independently controls 4 separate outputs.
A load is connected between battery voltage and the QDM, allowing the QDM driver to
control the output. Each QDM has fault detection logic which compares QDM driver input
and output voltages. The logic expects to measure less than 3 volts when the
QDM driver is ON and greater than 7 volts when OFF. The QDM has only 1 fault
line that will detect a fault on any of the 4 outputs. The scan tool can be
used to cycle the outputs ON or OFF. The scan tool can also perform an automated test
which can isolate the faulty circuit.
Conditions for Setting the DTC
Important: The QDM circuit is continuously checked when
the engine is running.
DTC P1640 and/or P1641 will set if:
| • | There is an open, short to ground, or short to voltage in the QDM output
LOW FUEL telltale lamp circuit. |
| • | A fault is detected for 5 seconds for DTC P1641. |
| • | A fault is detected for 20 seconds for DTC P1640. |
Diagnostic Aids
| • | If 1 output is faulty, the PCM will shut down only that QDM output
and not the entire quad driver unless the quad driver reaches its thermal limit, short
to voltage. At this time it will turn all 4 quad driver outputs OFF. When the
quad driver cools down it will turn back ON and this process will start over. |
| • | A shorted or open circuit or bulb can cause a code to set. |
| • | Check the 10 amp IGN 1 fuse in the IPJB. |
Use the Saturn service stall system, if available, to diagnose the quad driver
circuits or use a scan tool and perform an off-board QDM test.
When viewing QDM fault, using a scan tool dynamic display or MIL telltale, you
may notice the fault appears to be intermittent. This may be due to an intermittent
fault, but more likely it is due to the way the fault detection works.
For example, if the LOW FUEL telltale lamp is OFF, the PCM expects to refer
to 12 volts on the circuit line. If the circuit is open, 0 volts will
be measured on the circuit and the fault will be displayed. However, if the lamp is
turned ON, the PCM expects to measure 0 volts on the circuit and will not detect
a fault. This causes an intermittent problem because the lamp is not continuously
ON.
