GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2002 🢒 SL 🢒 Restraints 🢒 SIR 🢒 Headlining Trim Panel Replacement

Headlining Trim Panel Replacement Sedan - 1st Design

Removal Procedure

Some 2nd design vehicles may be equipped with an optional head curtain inflator module. Please read the following cautions before removing or installing vehicle components located near these supplementary restraint devices.

Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.


    Object Number: 863734 Size: SH
  1. If equipped with a sunroof, remove the bezel from the map lamp and the sunroof switch console by prying at the outside edge to unsnap the bezel.

    2. Object Number: 867104 Size: SH
  2. Remove the screws from the sunshade support and remove the support. Remove the screws from the sunshade and remove the shade. Refer to the following:
    3. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 867101 Size: SH
  3. Remove right front assist strap fastener cover by prying gently between headliner and cover on outboard side. Once the cover unsnaps from clip, push cover inward. Remove fasteners and remove assist strap. Refer to the following:
    4. • Clips (1)
    • Headliner (2)
    • Assist Straps (3)
    • Coathook (4)
  4. Remove the right front assist strap plate from behind the headliner.
  5. Open the rear assist strap fastener covers to expose the assist strap fasteners. Remove the fasteners and remove the assist straps.

    6. Object Number: 867261 Size: SH
  6. Remove the right front assist strap plate from behind the headliner.

    7. Object Number: 867259 Size: SH
  7. Open the rear assist strap fastener covers to expose the assist strap fasteners. Remove the fasteners and remove the assist straps.

    8. Object Number: 865246 Size: SH
  8. Remove the center high-mount stop lamp by pulling on the cover to disengage the attaching clips.
  9. Pull the headliner down at the left side center pillar location and disconnect the dome lamp harness from the body harness.
  10. Lower both the front seat backs to the full back position.

    11. Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced


    Object Number: 868086 Size: SH
  11. Reach above the headliner at the hook-and-loop retainer attachments. Gently disengage the hook-and-loop retainer attachments from the dual lock.
  12. For sunroof vehicles, gently disengage the left and right Velcro® along the sunroof opening first.

    13. Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  13. Remove the headliner through the right front door.

Installation Procedure
Object Number: 867107 Size: MF

Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  1. Transfer the dome lamp wire harness from the old headliner to the new headliner. Tape it into place. Refer to the following:
    2. • Coathooks (1)
    • Dome Lamp Retainer (2)
    • Dome Lamp (3)
    • Headliner (4)
    • Shade Supports (5)
    • Front Assist Strap (6)
    • Rear Assist Strap (7)
    • Coathook (8)
    • Sunshades (9)
  2. Insert the headliner through the right front door.
  3. Carefully center the headliner in the vehicle and loosely secure the headliner to the roof by applying light pressure at the hook-and-loop retainer locations.
  4. Connect the dome lamp wire harness at the left side center pillar location.

    5. Object Number: 867104 Size: SH
  5. Install the left and right side sunshade supports.
  6. Install the left and right side sunshades. Refer to the following:
    7. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 867101 Size: SH
  7. Position the assist strap plate behind the headliner at the right front assist strap location. Install the right front assist strap. Refer to the following:
    8. • Clips (1)
    • Headliner (2)
    • Assist Straps (3)
    • Coathook (4)
  8. Install the remaining assist straps.

    9. Object Number: 865246 Size: SH
  9. Install the center high-mount stop lamp cover.

    10. Object Number: 863734 Size: SH
  10. On vehicles equipped with a sunroof, install the map lamp and switch console cover.
  11. Press firmly at the hook-and-loop retainer locations to permanently secure the headliner at the center location.

    12. Object Number: 867261 Size: SH
  12. Install the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .
  13. Install the rear lock pillar upper moldings. Refer to Garnish Molding Replacement - Body Lock Pillar Upper .

    14. Object Number: 867259 Size: SH
  14. Raise the front seat backs.

Headlining Trim Panel Replacement Sedan - 2nd Design

Removal Procedure

Some 2nd design vehicles may be equipped with an optional head curtain inflator module. Please read the following cautions before removing or installing vehicle components located near these supplementary restraint devices.

Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.

Important: Before removal, note the position of the door weatherstrip over the edge of headliner.


    Object Number: 869328 Size: SH
  1. Remove the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    2. Object Number: 867104 Size: SH
  2. Remove the screws from the sunshade, the sunshade support and remove the support. Refer to the following:
    3. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 867261 Size: SH
  3. If equipped with a sunroof, remove the bezel from the map lamp and the sunroof switch console by prying at the outside edge to unsnap the bezel.

    4. Object Number: 869303 Size: SH

    Important: Rest the lock pillar moldings in the rear seat. It is not necessary to disconnect the shoulder belt from the molding to remove the headliner.

  4. Remove the right and left lock pillar upper garnish moldings. Refer to Garnish Molding Replacement - Body Lock Pillar Upper .

    5. Object Number: 869419 Size: SH
  5. Remove the coathook screws and the coathooks.

    6. Object Number: 865246 Size: SH
  6. Remove the center high-mount stop lamp trim cover by pulling it to disengage the clips.
  7. Pull the headliner down enough to disconnect dome lamp and center high-mount stop light wiring harnesses.
  8. Lower both the front seat backs to the ull back position.

    9. Object Number: 868086 Size: SH

    Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced

    Important:  On sunroof vehicles, it is carefully disengage the Velcro® along the right and left sides of the sunroof openings first.

  9. Reach above the hook-and-loop retainer attachments. Gently disengage hook-and-loop from the headliner Velcro®.
    10. • For non-sunroof vehicles Velcro® is located above the dome lamp.
    • For sunroof vehicles the Velcro® attachments surround the sunroof opening.

    Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  10. Remove the headliner through the right rear door.

Installation Procedure

Notice: When servicing the compressor, keep dirt and foreign material from getting on or into the compressor parts and system. Clean tools and clean work area are important for proper service. The compressor connections and the outside of the compressor should be cleaned before any ON CAR repairs, or before removal of the compressor. The parts must be kept clean at all times and any parts to be assembled should be cleaned with a non-petroleum based solvent and dried with air. Use only lint free cloths to wipe parts. Do not allow solvent to enter compressor or hoses.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.

Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.


    Object Number: 869451 Size: SH
  1. If the vehicle is equipped with a head curtain inflator module, ensure that the tether is correctly routed near the lock pillar.
    2. 1.1. Tether is routed below the coathook attachment area.
    1.2. Tether is securely fastened to the roof rail Velcro® pad.
    1.3. Ensure that there is no slack in the tether.

    Object Number: 869461 Size: SH
  2. Transfer the dome lamp and the center high-mount stop lamp wire harnesses from the old headliner to the new headliner and tape in place.

    3. Object Number: 869479 Size: SH
  3. Install the foam spacers at the rear corners of the headliner.
  4. Insert the headliner through the right rear door.
  5. Center the headliner in the vehicle and lift over the center pillar upper trim ledge to hold it in place.
  6. Apply light pressure at the hook and loop retainer locations to fasten it to headliner Velcro.

    7. Caution: Ensure that the curtain inflator module tether is not hanging below the edge of headliner. Improper routing can cause personal injury or improper curtain airbag deployment.

  7. Connect the dome lamp and center high-mount stop lamp wire harnesses.

    8. Object Number: 867104 Size: SH
  8. Install the left and right side sunshade and the sunshade supports and screws. Refer to the following:
    9. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 869419 Size: SH
  9. Install the coathooks and the coathook screws.

    10. Object Number: 865246 Size: SH
  10. Install the center high-mount stop lamp trim cover.

    11. Object Number: 867261 Size: SH
  11. On vehicles equipped with a sunroof, install the map lamp and switch console cover.

    12. Object Number: 869303 Size: SH
  12. Install the lock pillar upper garnish moldings. Refer to Garnish Molding Replacement - Body Lock Pillar Upper .

    13. Object Number: 869328 Size: SH
  13. Install the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    14. Object Number: 869471 Size: SH
  14. Reposition the door weatherstrip over the edge of the headliner above the door openings.

    15. Object Number: 869448 Size: SH
  15. Raise the front seat back.

Headlining Trim Panel Replacement Wagon - 1st Design

Removal Procedure

Some 2nd design vehicles may be equipped with an optional head curtain inflator module. Please read the following cautions before removing or installing vehicle components located near these supplementary restraint devices.

    Caution: Ensure that curtain inflator module tether is not caught behind upper fill tube bolt. Improper routing can cause personal injury or improper curtain airbag deployment.

    Caution: Improper routing of the curtain inflator module tether can cause personal injury or improper curtain airbag deployment

    Caution: If fill tube is damaged or kinked in any way the head curtain inflator module must be replace. Failure to replace can cause personal injury or improper curtain airbag deployment.

    Caution: Ensure that the curtain inflator module tether is not hanging below the edge of headliner. Improper routing can cause personal injury or improper curtain airbag deployment.

    Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

    Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.


    Object Number: 867104 Size: SH
  1. Remove the screws from the sunshade supports and remove the retainers. Remove the screws from the sunshades and remove the sunshades. Refer to the following:
    2. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 867101 Size: SH
  2. Remove the right assist strap fastener cover by prying gently between the headliner and the cover on the outboard side. Once the cover unsnaps from the clip, push the cover inward. Remove the fasteners and remove the assist strap.
    3. • Clips (1)
    • Headliner (2)
    • Assist Straps (3)
    • Coathook (4)
  3. Remove the right front assist strap plate from behind the headliner.
  4. Open the rear assist strap fastener covers to expose the assist strap fasteners. Remove the fasteners and remove the assist straps.

    5. Object Number: 867261 Size: SH
  5. Remove the corner upper garnish moldings. Refer to Body Rear Corner Trim Panel Replacement .

    6. Object Number: 879824 Size: SH
  6. Remove the lock pillar upper moldings. Refer to Body Lock Pillar Upper Molding Replacement .

    7. Object Number: 867189 Size: SH
  7. Remove the corner upper garnish moldings. Refer to Body Rear Corner Trim Panel Replacement .

    8. Object Number: 867189 Size: SH
  8. Remove the headliner rear upper trim finish molding.

    9. Object Number: 866919 Size: SH
  9. Pull the headliner down at the left side D-pillar location and disconnect the front dome lamp/rear dome lamp harness from the body harness.

    10. Object Number: 866919 Size: SH

    Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced

  10. Carefully reach above the headliner at the hook-and-loop retainer attachments to disengage the hook-and-loop retainer attachments.

    11. Object Number: 867171 Size: MF

    Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  11. Remove the headliner through the rear of the vehicle. Refer to the following:
    12. •  Rear Assist Strap (1)
    •  Front Dome Lamp Retainer (2)
    •  Coathook (3)
    •  Front Dome Lamp (4)
    •  Clip (5)
    •  Rear Dome Lamp Retainer (6)
    •  Headliner (7)
    •  Rear Dome Lamp (8)
    •  Sunshade Supports (9)
    •  Front Assist Straps (10)
    •  Sunshades (11)
    •  Coathook (12)

Installation Procedure

    Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  1. Transfer the dome lamps and the harness from old the headliner to new the headliner. Tape it into place.
  2. Route the dome lamp harness to the headliner using the same locations as removed from the old headliner. Connect the harness to the dome lamps.
  3. Secure the wire harness to the headliner with hot melt glue or tape to ensure the wire will not rattle in the vehicle.
  4. Insert the headliner through the rear of the vehicle.
  5. Center the headliner in the vehicle and loosely secure the headliner to the roof by applying light pressure at the hook-and-loop retainer locations.
  6. Connect the dome lamp/rear dome lamp wire harness at the left side D-pillar location.

    7. Object Number: 867104 Size: SH
  7. Install the left and the right side sunshade supports.
  8. Install the left and the right side sunshades. Refer to the following:
    9. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 867101 Size: SH
  9. Position the assist strap plate behind the headliner at the right front assist strap location. Install the right front assist strap.
    10. • Clips (1)
    • Headliner (2)
    • Assist Straps (3)
    • Coathook (4)
  10. Install the remaining assist straps.

    11. Object Number: 866919 Size: SH
  11. Install the headliner rear upper trim finish molding.
  12. Press firmly at the hook-and-loop retainer locations to permanently secure the headliner at the hook-and-loop retainer locations.

    13. Object Number: 867261 Size: SH
  13. Install the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    14. Object Number: 879824 Size: SH
  14. Install the lock pillar upper garnish moldings. Refer to Body Lock Pillar Upper Molding Replacement .

    15. Object Number: 867189 Size: SH
  15. Install the corner upper moldings. Refer to Body Rear Corner Trim Panel Replacement .

Headlining Trim Panel Replacement Wagon - 2nd Design

Removal Procedure

Some 2nd design vehicles may be equipped with an optional head curtain inflator module. Please read the following cautions before removing or installing vehicle components located near these supplementary restraint devices.

    Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

    Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

    Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.


    Object Number: 869328 Size: SH

    Important: Before removing, note the position of the door weatherstrip over the edge of theheadliner.

  1. Remove the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    2. Object Number: 867104 Size: SH
  2. Remove the screws from the sunshade supports and the sunshades. Remove the sunshade supports and the sunshades. Refer to the following:
    3. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 869300 Size: SH
  3. Remove the body lock pillar upper garnish moldings. Refer to Garnish Molding Replacement - Body Lock Pillar Upper .

    4. Object Number: 867189 Size: SH
  4. Remove the corner upper garnish moldings. Refer to Body Rear Corner Trim Panel Replacement .

    5. Object Number: 866919 Size: SH
  5. Remove the rear header trim panel by pulling at the clip locations to disengage.
  6. Remove the coathook screws and the coathooks.
  7. Pull the headliner down slightly to disconnect the front and rear dome lamp wiring harnesses.

    8. Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced

  8. Reach above the headliner at the dome lamp locations and disengage the hook and loop retainers.

    9. Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  9. Remove the headliner through the rear of the vehicle.

Installation Procedure
Object Number: 867173 Size: MF

Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.


    Object Number: 869451 Size: SH

    Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  1. If the vehicle is equipped with a head curtain inflator module, ensure that the tether is correctly routed near the lock pillar.
    2. 1.1. Tether is routed below the coathook attachment area.
    1.2. Tether is securely fastened to the roof rail Velcro® pad.
    1.3. Ensure that there is no slack in the tether.

    Object Number: 869461 Size: SH
  2. Transfer the dome lamp wiring harness from the old headliner to the new and tape in place.

    3. Object Number: 869479 Size: SH
  3. Install the foam spacers at the rear corners of the headliner.
  4. Insert the headliner through the rear of the vehicle.
  5. Center the headliner in the vehicle and lift it over the center pillar upper trim ledge to hold in place.
  6. Apply light pressure at the hook and loop retainer locations located above the dome lamps to engage.

    7. Caution: Ensure that the curtain inflator module tether is not hanging below the edge of headliner. Improper routing can cause personal injury or improper curtain airbag deployment.


    Object Number: 867104 Size: SH
  7. Connect the dome lamp wire harness.
  8. Install the sunshade, the sunshade supports and the screws. Refer to the following:
    9. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 869419 Size: SH
  9. Install the coathooks and the coathook screws.

    10. Object Number: 866919 Size: SH
  10. Install the rear upper trim finish molding.

    11. Object Number: 869300 Size: SH
  11. Install the body lock pillar upper garnish moldings. Refer to Body Lock Pillar Upper Molding Replacement .

    12. Object Number: 867189 Size: SH
  12. Install the corner upper garnish moldings. Refer to Body Rear Corner Trim Panel Replacement .

    13. Object Number: 869328 Size: SH
  13. Install the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    14. Object Number: 869344 Size: SH
  14. Reposition the door weatherstrip over the edge of the headliner above the door openings.

Headlining Trim Panel Replacement Coupe - 1st Design

Removal Procedure

    Object Number: 863734 Size: SH

    Important: LHD shown, RHD similar.

  1. If equipped with a sunroof, remove the bezel from the map lamp and the sunroof switch console by prying at the outside edge to unsnap the bezel.

    2. Object Number: 867104 Size: SH
  2. Remove the screws from the sunshade support.
  3. Remove the screws from the sunshade and remove the shade. Refer to the following:
    4. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 868577 Size: SH
  4. Remove the seat belt retractor cover.

    5. Object Number: 868093 Size: SH
  5. Remove the assist strap fastener cover by prying gently between the headliner and the cover on the outboard side. Once the cover unsnaps from the clip, push the cover inward. Remove the fasteners and remove the assist strap.

    6. Object Number: 868083 Size: SH
  6. Remove the instrument panel upper trim panel. Refer to Instrument Panel Upper Trim Plate Replacement in Instrument Panel, Gages, and Console.
  7. Remove the windshield garnish moldings. Start at the upper rear section of the molding and pull firmly at the clip locations to disengage the molding from the vehicle.

    8. Object Number: 868093 Size: SH
  8. Remove the assist strap plate from behind the headliner.

    9. Object Number: 868082 Size: SH
  9. Remove the coathooks by inserting a small screwdriver blade between the outside of the hook and the center section. Apply pressure to force the center section outward.

    10. Object Number: 865246 Size: SH
  10. Remove the center high-mount stop lamp cover by pulling on the cover to disengage the attaching clips.
  11. Disconnect the center high-mount stop lamp harness electrical connector.

    12. Object Number: 878115 Size: SH
  12. Unsnap the seat belt bolt cover.
  13. Loosen the Torx® fastener and rotate the presenter arm forward to disengage the presenter arm guide notch from the spaceframe.
  14. Remove the presenter arm and the seat belt unit.
  15. Lower both the front seat backs to full back position.

    16. Object Number: 868060 Size: SH
  16. Remove the quarter window garnish moldings by pulling to disengage the attaching clips. Refer to the following:
    17. • Defogger Lead (1)
    • Defogger Notch (2)
    • Interlock Tab (3)
  17. Disconnect the dome lamp electrical connector at the spaceframe on the driver's side.
  18. If equipped with a sunroof, disconnect the sunroof connector on the passenger's side.

    19. Object Number: 868086 Size: SH

    Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced

    Important: On vehicles equipped with a sunroof, gently disengage the Velcro® along the right and left sides of the sunroof opening first.

  19. On vehicle equipped with a sunroof, reach above the headliner at the hook-and-loop retainer attachments. Gently disengage the hook-and-loop retainer attachments from the dual lock.

    20. Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

  20. Remove the headliner through the left doors.

Installation Procedure

Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

Important: LHD shown; RHD similar.


    Object Number: 868093 Size: SH
  1. Transfer the dome lamp assembly and the wire harness from the old headliner to the new headliner. Tape the harness in place.
  2. Insert the headliner through the left doors.
  3. On vehicles equipped with a sunroof, center the headliner in the vehicle and loosely secure the headliner to the roof.
  4. Install the sunshades.
  5. Position the assist strap plate behind the headliner at the assist strap location.
  6. Install the assist strap.

    7. Object Number: 863734 Size: SH
  7. On vehicles equipped with a sunroof, install a map lamp and a sunroof switch cover.
  8. Connect the dome lamp electrical connector at the spaceframe on the driver's side.
  9. On vehicles equipped with a sunroof, connect the sunroof harness electrical connector on the passenger's side.

    10. Object Number: 865246 Size: SH
  10. Connect the electrical connector at the center high-mount stop lamp.
  11. Install the center high-mount stop lamp cover.

    12. Object Number: 868060 Size: SH
  12. Install the quarter window garnish moldings. Insert the front of the molding and work towards the rear of vehicle. Ensure the interlocking tab is engaged.
    13. • Defogger Lead (1)
    • Defogger Notch (2)
    • Interlock Tab (3)

    Object Number: 868082 Size: SH
  13. Ensure the center of the coathooks are extended.
  14. Place the coathooks in the quarter window garnish moldings hole.
  15. Once the hooks are seated in the spaceframe, push the center of the hooks in to lock it in place.

    16. Object Number: 868577 Size: SH
  16. Install the seat belt retractor cover.

    17. Object Number: 868086 Size: SH
  17. On vehicles equipped with a sunroof, firmly press on the hook-and-loop retainer locations to permanently secure the headliner at the center location.

    18. Object Number: 868083 Size: SH
  18. Place the forward edge of the molding to the windshield pillar base. Align the clips and firmly push to engage the molding clips at the forward edge of the vehicle.
  19. Install the instrument panel upper trim panel. Refer to Instrument Panel Upper Trim Plate Replacement in Instrument Panel, Gages, and Console.

    20. Object Number: 868120 Size: MH

    Caution: Observe the orientation of the presenter arm assembly and the seat belt unit. Incorrect orientation may result in personal injury.

    Caution: Apply Loctite 242® Threadlocker US P/N 12345382 (Canadian P/N 10953489), or equivalent, on all restraint bolts/nuts before installation. Failure to use such threadlocker correctly may result in personal injury.

  20. Install the presenter arm and the seat belt unit. Refer to Seat Belt Retractor Replacement - Right Front in Seat Belts.

    21. Tighten
    Tighten presenter arm bolt to 50 N·m (37 lb ft).

Headlining Trim Panel Replacement Coupe - 2nd Design

Removal Procedure

Some 2nd design vehicles may be equipped with an optional head curtain inflator module. Please read the following cautions before removing or installing vehicle components located near these supplementary restraint devices.

Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.

Important:  Before removing, note the position of the door weather-strip over the edge of headliner.


    Object Number: 869328 Size: SH
  1. Remove the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    2. Object Number: 863734 Size: SH
  2. If equipped with a sunroof, remove the bezel from the map lamp and the sunroof switch console by prying at the outside edge to unsnap the bezel.

    3. Object Number: 869334 Size: SH
  3. Remove the striker trim cover. Refer to Striker Cover Replacement .

    4. Object Number: 867104 Size: SH
  4. Remove the sunshades, the sunshade supports, and the screws.
    5. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 869419 Size: SH
  5. Remove the left coat hook and the coat hook screw.

    6. Object Number: 865246 Size: SH
  6. Remove the center high-mount stop lamp cover by pulling to disengage the clips.
  7. Disconnect the wiring harness.

    8. Object Number: 868115 Size: SH
  8. Unsnap the seat belt bolt cover.
  9. Loosen the TORX® bolt and rotate the presenter arm forward to disengage the presenter arm guide notch from the spaceframe.
  10. Remove the presenter arm and the seat belt unit.
  11. Lower both the front seat backs to the full back position.

    12. Object Number: 868060 Size: SH
  12. Remove the quarter window garnish moldings by pulling to disengage the clips.
    13. • Defogger Lead (1)
    • Defogger Notch (2)
    • Interlock Tab (3)
  13. Disconnect the dome lamp electrical connector at the spaceframe on the driver's side.

    14. Object Number: 868086 Size: SH

    Notice: When removing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.

    Notice: When removing a headliner it is possible for the Velcro® fasteners to tear from the headliner substrate. The Velcro® to hook and loop bond is much stronger than the Velcro® to substrate. Once damaged, the Velcro® cannot be replaced

  14. Reach above the hook and loop retainer. Gently disengage them from the headliner Velcro®.
    15. • For non-sunroof vehicles, the Velcro® is located above the dome lamp.
    • For sunroof vehicles, the Velcro® attachments surround the sunroof opening. Disengage the Velcro® along the left and right sides first.

    Object Number: 869331 Size: SH
  15. Slide the seat belt webbing bezel outboard to disengage it from the slot in the headliner.
  16. Remove the headliner through left side.

Installation Procedure

Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

Caution: The head curtain inflator module tethers must be routed correctly. Improper routing may result in personal injury or improper curtain airbag deployment.

Notice: When installing the headliner, be careful not to bend the headliner. If the headliner is bent, it will break and leave a wrinkle that cannot be repaired.


Object Number: 869341 Size: SH

    Object Number: 869468 Size: SH
  1. If a vehicle is equipped with a head curtain inflator module ensure that tether is correctly routed near the lock pillar.
    2. • Tether is routed below the coat hook attachment area.
    • Tether is securely fastened to the roof rail Velcro® pad.
    • Ensure that there is no slack in the tether.
  2. Transfer the dome lamp wire harness and tape it in place.
  3. Insert the headliner through the left doors.

    4. Object Number: 869331 Size: SH
  4. Slide the seat belt webbing bezel into the slot in the headliner.
  5. Center the headliner and apply pressure at the hook and loop locations.

    6. Object Number: 867104 Size: SH

    Caution: Ensure that the curtain inflator module tether is not hanging below the edge of headliner. Improper routing can cause personal injury or improper curtain airbag deployment.

  6. Connect the dome lamp and the high mount stop lamp wire harness.
  7. Install the sunshade, the sunshade supports, and the screws.
    8. • Headliner (1)
    • Sunshade Support (2)
    • Sunshade (3)

    Object Number: 869419 Size: SH
  8. Install the coat hook and the coat hook screw.
  9. Install the high-mount stop lamp trim cover.

    10. Object Number: 863734 Size: SH
  10. On vehicles with a sunroof, install the map lamp and the switch console cover.

    11. Object Number: 868060 Size: SH
  11. Install the quarter window garnish moldings.

    12. Caution: Observe the orientation of the presenter arm assembly and the seat belt unit. Incorrect orientation may result in personal injury.

    Caution: Apply Loctite 242® Threadlocker US P/N 12345382 (Canadian P/N 10953489), or equivalent, on all restraint bolts/nuts before installation. Failure to use such threadlocker correctly may result in personal injury.

  12. Install the presenter arm and the seat belt unit. Refer to Seat Belt Retractor Replacement - Right Front in Seat Belts.

    13. Object Number: 869334 Size: SH
  13. Install the striker trim cover. Refer to Striker Cover Replacement .

    14. Object Number: 869328 Size: SH
  14. Install the windshield garnish moldings. Refer to Windshield Garnish Molding Replacement .

    15. Object Number: 869444 Size: SH
  15. Reposition the door weather-strip over the headliner edge.
  16. Raise the front seat backs.