GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2002 🢒 VUE - AWD 🢒 Engine 🢒 Engine Controls - 3.0L (L81) 🢒 DTC P0172 or P0175

Circuit Description

The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy and emission control. Fuel delivery is controlled differently during Open and Closed Loop. During Open Loop the ECM determines fuel delivery based on sensor signals, without oxygen sensor input. During Closed Loop, the oxygen sensor inputs are added and used by the ECM to calculate fuel trim. If the oxygen sensors indicate a lean condition, fuel trim values will be above 0 percent. If the oxygen sensors indicate a rich condition, fuel trim values will be below 0 percent. Short term fuel trim (FT) values change rapidly in response to the heated oxygen sensor (HO2S) voltage signals. Long term FT values change slower in response to trends in short term FT adjustments. The fuel trim diagnostic will conduct a test to determine if a rich failure actually exists or if excessive vapor from the evaporative emission (EVAP) canister is causing a rich condition. If the ECM detects excessive vapor, then a pass is logged. This DTC is continuously monitored during operation. If the ECM detects an excessively rich condition, DTC P0172 or P0175 sets.

Conditions for Running the DTC
    • DTC P0030, P0031, P0032, P0050, P0051, P0052, P0101, P0102, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0103, P0130, P0131, P0132, P0133, P0134, P0135, P0150, P0151, P0152, P0153, P0155, P0201-P0206, P0221,P0222, P0223, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277 are not set.
    • The system is in Closed Loop status.
    • The fuel level is more than 9.8 percent.

Conditions for Setting the DTC
    • The LT FT Cruise/Accel parameter is below -23 percent.
        OR
    • THE LT FT Idle/Decel parameter is below -8.1 percent.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
    • A skewed mass air flow (MAF) sensor may set this DTC. Refer to DTC P0101 .
    • Fuel contamination, such as water and alcohol, will effect fuel trim.
    • A skewed engine coolant temperature (ECT) sensor may set this DTC.
    • An EVAP purge solenoid that is stuck open may set this DTC.
    • Review the Failure Records with a scan tool. If an intermittent condition is suspected , refer to Intermittent Conditions .

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If any DTCs are set other than DTC P0172 or P0175, refer to those DTCs before continuing.

  1. Install a scan tool.
  2. Start the engine.
  3. Operate the vehicle within the Conditions for Running the DTC.
  4. Record the LT FT Cruise/Accel and LT FT Idle/Decel parameter values.
  5. Turn OFF the engine.
  6. Turn ON ignition, with engine OFF.
  7. Review the Freeze Frame/Failure Records and record the displayed data for this DTC.

Does the scan tool indicate that the LT FT Cruise/Accel parameter is less than the specified value?

-23%

Go to Step 4

Go to Step 3

3

Does the scan tool indicate that the LT FT Idle/Decel parameter is less than the specified value?

-8.1%

Go to Step 4

Go to Diagnostic Aids

4
  1. Operate the engine at idle.
  2. Observe the heated oxygen sensor (HO2S) parameters with a scan tool.

Does the scan tool indicate that the values are within the specified range and fluctuating?

200-800 mV

Go to Step 5

Go to Step 6

5

  1. Turn OFF the engine.
  2. Visually and physically inspect the following items:
    3. • The inlet screen of the mass air flow (MAF) sensor for blockage
    • The vacuum hoses for splits, kinks, and proper connections.
    • The air intake duct for being collapsed or restricted
    • The air filter for being dirty or restricted
    • Objects blocking the throttle body

Did you find and correct the condition?

--

Go to Step 8

Go to Step 7

6

  1. Turn OFF the engine.
  2. Inspect the HO2S for proper installation.
  3. Verify that the electrical connectors and wires are secured and are not contacting the exhaust system.

Did you find and correct the condition?

--

Go to Step 8

Go to Fuel System Diagnosis

7
  1. Inspect for the following conditions:
    2. • Excessive fuel in the crankcase
    • The evaporative emissions (EVAP) control system--Refer to Service Bay Test .
    • The fuel pressure regulator for proper operation--Refer to Fuel System Diagnosis .
  2. Perform the Fuel Injector Balance Test.

Did you find and correct the condition?

--

Go to Step 8

Go to Symptoms-Engine Mechanical in Engine Mechanical

8

Important: After repairs, reset the Long Term Fuel with the scan tool Fuel Trim Reset function.

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 9

9

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK