GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2002 🢒 VUE - AWD 🢒 Preface 🢒 Cautions and Notices 🢒 Headlining Trim Panel Replacement

Removal Procedure

    Notice: Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

    Notice: If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling and SIR Disabling and Enabling in SIR.
  2. Remove the sunshade. Refer to Sunshade Replacement .
  3. Remove the optional reading lamp cover. Refer to Reading Lamp Replacement in Lighting Systems.

    4. Object Number: 980764 Size: SH
  4. Disconnect the optional OnStar® microphone harness.
  5. Disconnect the optional sunroof switch.
  6. Remove the windshield upper garnish molding. Refer to Center Pillar Upper Garnish Molding Replacement .
  7. Remove the upper center pillar molding. Refer to Center Pillar Lower Garnish Molding Replacement .
  8. Remove the dome lamp. Refer to Dome Lamp Replacement in Lighting Systems.
  9. Remove the lock pillar garnish molding. Refer to Lock Pillar Upper Garnish Molding Replacement .

    10. Object Number: 981002 Size: SH
  10. Remove the rear window trim moldings by gently pulling at the clip locations.
  11. Remove the rear corner garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  12. Remove the coat hooks. Refer to Coat Hook Replacement .
  13. Remove the rear pushpin.
  14. Pull back the quarter trim panel. Refer to Rear Quarter Lower Trim Panel Replacement .
  15. Remove the door seal from the headliner edge.
  16. Disconnect the headliner electrical connector behind the trim panel.

    17. Object Number: 977468 Size: SH
  17. Fold the passenger seat flat and the driver seat forward.
  18. Carefully disengage the Velcro® and the magnet attachments from the headliner and remove the headliner out from the liftgate opening.

Installation Procedure

    Object Number: 977468 Size: SH
  1. Position the headliner into the vehicle through the liftgate opening.
  2. Push on the Velcro® and the magnet attachments to partially secure the liner.
  3. Install the pushpin fastener at the rear of the headliner.
  4. Secure the weatherstrip over the edge of the headliner.
  5. Connect the sunroof switch electrical connectors.

    6. Object Number: 980764 Size: SH
  6. Connect the OnStar® microphone electrical connector.
  7. Install the reading lamp cover. Refer to Reading Lamp Replacement in Lighting Systems.
  8. Connect the OnStar® electrical connector.
  9. Install the sunshades. Refer to Sunshade Replacement .
  10. Install the windshield upper garnish molding. Refer to Center Pillar Upper Garnish Molding Replacement
  11. Install the center pillar molding. Refer to Center Pillar Lower Garnish Molding Replacement .
  12. Install the dome lamp. Refer to Dome Lamp Replacement .

    13. Object Number: 977398 Size: SH
  13. Connect the headliner electrical connectors behind the cargo area trim panel. Connect the clips holding the wire to the metal.
  14. Install the driver side trim panel.
  15. Install the lock pillar garnish moldings. Refer to Lock Pillar Upper Garnish Molding Replacement .
  16. Install the rear garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  17. Install the rear window upper moldings. Refer to Rear Window Upper Molding Replacement .
  18. Install the coat hooks. Refer to Coat Hook Replacement .
  19. Enable the SIR system. Refer to SIR Disabling and Enabling and SIR Disabling and Enabling in SIR.