When the radio is set at minimum volume, the plus (+) and minus (-) speaker outputs are approximately 5-6 volts measured to vehicle ground. As the volume increases, the plus and minus change to create a voltage difference between each other. This drives the voice coil of the speaker producing sound.
This Vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description in Vehicle DTC Information.
• | DTC B1025 LF Audio Output (+) Circuit |
• | DTC B1035 RF Audio Output (+) Circuit |
• | DTC B1045 LR Audio Output (+) Circuit |
• | DTC B1055 RR Audio Output (+) Circuit |
DTC Symptom | DTC Symptom Descriptor |
---|---|
01 | Short to Battery |
02 | Short to Ground |
04 | Open Circuit |
The following are conditions that must be present in order for the radio to enable the diagnostics.
• | The vehicle power mode is ACCESSORY, RUN, or RAP. |
• | The system voltage is at least 9.0 V and no more than 16.0 V. |
• | All the above conditions are present for greater than 250 ms. |
The following conditions are present for 250 ms or longer:
One of the speaker positive output circuits is shorted to battery.
The speaker positive output circuit is shorted to ground.
The speaker positive output circuit is open.
The radio disables the audio output to the speaker with the current fault.
• | The conditions for setting the DTC are no longer present. |
• | A history DTC clears after 100 malfunction free ignition cycles. |
• | The radio receives the clear code command from the scan tool. |
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Radio/Audio System Schematics Connector End View Reference: Entertainment Connector End Views | |||
1 | Did you review the Description and Operation? | Go to Step 2 | |
Does the scan tool indicate that DTC B1025, B1035, B1045, or B1055 is current? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | |
Test the affected speaker output channel from the radio to the speaker for a short to ground, short to voltage or an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 6 | Go to Step 4 | |
4 | Inspect for poor connections at the harness connector of the radio. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 6 | Go to Step 5 |
5 |
Important: Perform the radio set up procedure for the radio. Replace the radio. Refer to Radio Replacement and to Radio Setup . Did you complete the replacement? | Go to Step 6 | -- |
6 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
When the radio is set at minimum volume, the plus (+) and minus (-) speaker outputs are approximately 5-6 volts measured to vehicle ground. As the volume increases, the plus and minus change to create a voltage difference between each other. This drives the voice coil of the speaker producing sound.
This Vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description in Vehicle DTC Information.
• | DTC B1025 LF Audio Output (+) Circuit |
• | DTC B1035 RF Audio Output (+) Circuit |
• | DTC B1045 LR Audio Output (+) Circuit |
• | DTC B1055 RR Audio Output (+) Circuit |
DTC Symptom | DTC Symptom Descriptor |
---|---|
01 | Short to Battery |
02 | Short to Ground |
04 | Open Circuit |
The following are conditions that must be present in order for the radio to enable the diagnostics.
• | The vehicle power mode is ACCESSORY, RUN, or RAP. |
• | The system voltage is at least 9.0 V and no more than 16.0 V. |
• | All the above conditions are present for greater than 250 ms. |
The following conditions are present for 250 ms or longer:
One of the speaker positive output circuits is shorted to battery.
The speaker positive output circuit is shorted to ground.
The speaker positive output circuit is open.
The radio disables the audio output to the speaker with the current fault.
• | The conditions for setting the DTC are no longer present. |
• | A history DTC clears after 100 malfunction free ignition cycles. |
• | The radio receives the clear code command from the scan tool. |
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Radio/Audio System Schematics Connector End View Reference: Entertainment Connector End Views | |||
1 | Did you review the Description and Operation? | Go to Step 2 | |
Does the scan tool indicate that DTC B1025, B1035, B1045, or B1055 is current? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | |
Test the affected speaker output channel from the radio to the amplifier for a short to ground, short to voltage or an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 6 | Go to Step 4 | |
4 | Inspect for poor connections at the harness connector of the radio. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 6 | Go to Step 5 |
5 |
Important: Perform the radio set up procedure for the radio. Replace the radio. Refer to Radio Replacement and to Radio Setup . Did you complete the replacement? | Go to Step 6 | -- |
6 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |