GM Service Manual Online
For 1990-2009 cars only

Inflatable Restraint Passenger Presence System Replacement - Front with Heated Seat


Object Number: 1554742  Size: MF

Callout

Component Name

Caution: Replace the passenger presence system as a complete assembly to prevent possible injury to the occupant. All the components in the service kit are assembled and calibrated as a unit. Using only some of the components in the service kit will cause the passenger presence system to operate improperly.

Caution: To avoid personal injuries, re-zero the passenger presence system whenever you remove or replace the seat cushion or trim. Failure to do so may cause the system to malfunction.

Notice: Refer to Fastener Notice in the Preface section.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

Preliminary Procedure

  1. Remove the front bucket seat. Refer to Front Seat Replacement - Bucket .
  2. Remove the recliner handle. Refer to Driver Seat and Passenger Seat Recliner Handle Replacement .
  3. Remove the seat cushion outer trim panel. Refer to Front Seat Cushion Outer Trim Panel Replacement .
  4. Re-zero the inflatable restraint passenger presence system whenever the seat cushion or any component of the passenger presence system is removed. Refer to Passenger Presence System Rezeroing .

1

Cover, Passenger Seat Cushion

Refer to Front Seat Cushion Cover and Pad Replacement .

2

Heater, Seat Cushion

Tip
Disconnect the electrical connector.

3

Sensor, Inflatable Restraint Passenger Presence System

Tip

  1. Note the routing of the wiring harness and connector location for installation.
  2. Disconnect the electrical connector.

4

Pad, Passenger Seat Cushion

5

Screw, Inflatable Restraint Passenger Presence Module (Qty: 3)

Tighten
2 N·m (18 lb in)

6

Module, Inflatable Restraint Passenger Presence Module

Tip
Remove module from bracket to replace.

Refer to Control Module References for programming and setup information.

Inflatable Restraint Passenger Presence System Replacement - Front without Heated Seat


Object Number: 1554769  Size: MF

Callout

Component Name

Caution: Replace the passenger presence system as a complete assembly to prevent possible injury to the occupant. All the components in the service kit are assembled and calibrated as a unit. Using only some of the components in the service kit will cause the passenger presence system to operate improperly.

Caution: To avoid personal injuries, re-zero the passenger presence system whenever you remove or replace the seat cushion or trim. Failure to do so may cause the system to malfunction.

Notice: Refer to Fastener Notice in the Preface section.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

Preliminary Procedure

  1. Remove the front bucket seat. Refer to Front Seat Replacement - Bucket .
  2. Remove the recliner handle. Refer to Driver Seat and Passenger Seat Recliner Handle Replacement .
  3. Remove the seat cushion outer trim panel. Refer to Front Seat Cushion Outer Trim Panel Replacement .
  4. Re-zero the inflatable restraint passenger presence system whenever the seat cushion or any component of the passenger presence system is removed. Refer to Passenger Presence System Rezeroing .
  5. Refer to Control Module References for programming and setup information.

1

Cover, Passenger Seat Cushion

Refer to Front Seat Cushion Cover and Pad Replacement .

2

Sensor, Inflatable Restraint Passenger Presence System

Tip

  1. Note the routing of the wiring harness and connector location for installation.
  2. Disconnect the electrical connector.

3

Pad, Passenger Seat Cushion

4

Screw, Inflatable Restraint Passenger Presence Module (Qty: 3)

Tighten
2 N·m (18 lb in)

5

Module, Inflatable Restraint Passenger Presence Module

Tip
Remove module from bracket to replace.