Radiator Replacement L61

1. Drain the cooling system. Refer to Cooling System Draining and Filling .
2. Remove the front fascia. Refer to Front Bumper Fascia Replacement .
3. Remove the battery box inlet air duct.



4. Remove the condenser radiator fan module (CRFM) closeout panel retainers from the condenser.
5. Remove the CRFM closeout panel from the condenser.



6. Remove the fan assembly bolts from the radiator.
7. Lift the fan assembly to disengage the lower retention tabs.
8. Position the fan assembly away from the radiator.



9. Lift the condenser while holding the upper retention tabs forward.
10. Position the condenser away from the radiator.
11. Disconnect the transmission cooler lines from the radiator, if equipped.



12. Remove the CRFM bracket bolts from the radiator support.
13. Remove the CRFM brackets from the radiator.



14. Remove the radiator inlet hose clamp from the radiator.
15. Remove the radiator inlet hose from the radiator.



16. Remove the radiator outlet hose clamp from the radiator.
17. Remove the radiator outlet hose from the radiator.



18. Remove the radiator from the vehicle.
19. Remove the radiator seals from the radiator.

1. Install the radiator seals to the radiator.
2. Install the radiator to the vehicle.



3. Install the radiator outlet hose to the radiator.
4. Install the radiator outlet hose clamp to the radiator.



5. Install the radiator inlet hose to the radiator.
6. Install the radiator inlet hose clamp to the radiator.



7. Install the CRFM bracket to the radiator support.

Notice: Refer to Fastener Notice in the Preface section.

8. Install the CRFM brackets bolts to the radiator.

Tighten
Tighten the bolt to 8 N·m (71 lb in).

9. Connect the transmission cooler lines to the radiator, if equipped.

Tighten
Tighten the fittings to 16 N·m (12 lb ft).




10. Install the condenser to the radiator. Press down to engage the upper retention tabs.



11. Install the fan assembly to the radiator.
12. Install the fan assembly bolts to the radiator.

Tighten
Tighten the bolts to 8 N·m (71 lb in).




13. Install the CRFM closeout panel to the condenser.
14. Install the CRFM closeout panel retainers to the condenser.



15. Install the battery box inlet air duct.
16. Install the front fascia. Refer to Front Bumper Fascia Replacement .
17. Fill the cooling system. Refer to Cooling System Draining and Filling .

Radiator Replacement L66

1. Drain the cooling system. Refer to Cooling System Draining and Filling .
2. Remove the front fascia. Refer to Front Bumper Fascia Replacement .
3. Remove the condenser radiator fan module (CRFM) closeout panel retainers from the condenser.
4. Remove the CRFM closeout panel from the condenser.



5. Remove the fan assembly bolts from the radiator.
6. Lift the fan assembly to disengage the lower retention tabs.
7. Position the fan assembly away from the radiator.



8. Lift the condenser while holding the upper retention tabs forward.
9. Position the condenser away from the radiator.



10. Disconnect the transmission cooler lines from the radiator.



11. Remove the CRFM bracket bolts from the radiator support.
12. Remove the CRFM brackets from the radiator.



13. Remove the radiator inlet hose clamp from the radiator.
14. Remove the radiator inlet hose from the radiator.



15. Remove the radiator outlet hose clamp from the radiator.
16. Remove the radiator outlet hose from the radiator.



17. Remove the radiator from the vehicle.
18. Remove the radiator seals from the radiator.

1. Install the radiator seals to the radiator.
2. Install the radiator to the vehicle.



3. Install the radiator outlet hose to the radiator.
4. Install the radiator outlet hose clamp to the radiator.



5. Install the radiator inlet hose to the radiator.
6. Install the radiator inlet hose clamp to the radiator.



7. Install the CRFM bracket to the radiator support.

Notice: Refer to Fastener Notice in the Preface section.

8. Install the CRFM brackets bolts to the radiator.

Tighten
Tighten the bolt to 8 N·m (71 lb in).




9. Connect the transmission cooler lines to the radiator.



10. Install the condenser to the radiator. Press down to engage the upper retention tabs.



11. Install the fan assembly to the radiator.
12. Install the fan assembly bolts to the radiator.

Tighten
Tighten the bolts to 8 N·m (71 lb in).




13. Install the CRFM closeout panel to the condenser.
14. Install the CRFM closeout panel retainers to the condenser.
15. Install the front fascia. Refer to Front Bumper Fascia Replacement .
16. Fill the cooling system. Refer to Cooling System Draining and Filling .

Radiator Replacement LAT

1. Drain the cooling system. Refer to Cooling System Draining and Filling .
2. Remove the front fascia. Refer to Front Bumper Fascia Replacement .
3. Remove the battery box inlet air duct.



4. Remove the condenser radiator fan module (CRFM) closeout panel retainers from the condenser.
5. Remove the CRFM closeout panel from the condenser.



6. Remove the fan assembly bolts from the radiator.
7. Lift the fan assembly to disengage the lower retention tabs.
8. Position the fan assembly away from the radiator.
9. Remove the front bumper impact bar. Refer to Front Bumper Impact Bar Replacement.



10. Lift the condenser while holding the upper retention tabs forward.
11. Position the condenser away from the radiator.
12. Disconnect the transmission cooler lines from the radiator, if equipped.



13. Remove the CRFM bracket bolts from the radiator support.
14. Remove the CRFM brackets from the radiator.



15. Remove the radiator inlet hose clamp from the radiator.
16. Remove the radiator inlet hose from the radiator.



17. Remove the radiator outlet hose clamp from the radiator.
18. Remove the radiator outlet hose from the radiator.



19. Remove the radiator from the vehicle.
20. Remove the radiator seals from the radiator.

1. Install the radiator seals to the radiator.
2. Install the radiator to the vehicle.



3. Install the radiator outlet hose to the radiator.
4. Install the radiator outlet hose clamp to the radiator.



5. Install the radiator inlet hose to the radiator.
6. Install the radiator inlet hose clamp to the radiator.



7. Install the CRFM bracket to the radiator support.

Notice: Refer to Fastener Notice in the Preface section.

8. Install the CRFM brackets bolts to the radiator.

Tighten
Tighten the bolt to 8 N·m (71 lb in).

9. Connect the transmission cooler lines to the radiator, if equipped.

Tighten
Tighten the fittings to 16 N·m (12 lb ft).




10. Install the condenser to the radiator. Press down to engage the upper retention tabs.



11. Install the fan assembly to the radiator.
12. Install the fan assembly bolts to the radiator.

Tighten
Tighten the bolts to 8 N·m (71 lb in).

13. Install the front bumper impact bar. Refer to Front Bumper Impact Bar Replacement.



14. Install the CRFM closeout panel to the condenser.
15. Install the CRFM closeout panel retainers to the condenser.



16. Install the battery box inlet air duct.
17. Install the front fascia. Refer to Front Bumper Fascia Replacement .
18. Fill the cooling system. Refer to Cooling System Draining and Filling .