GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Circuit/System Description

The control module enables the fuel pump relay when the ignition switch is turned ON. The control module will disable the fuel pump relay within 2 seconds unless the control module detects ignition reference pulses. The control module continues to enable the fuel pump relay as long as ignition reference pulses are detected. The control module disables the fuel pump relay within 2 seconds if ignition reference pulses cease to be detected and the ignition remains ON.

The fuel system is a returnless on-demand design. The fuel pressure regulator is a part of the primary fuel tank module, eliminating the need for a return pipe from the engine. A returnless fuel system reduces the internal temperature of the fuel tank by not returning hot fuel from the engine to the fuel tank. Reducing the internal temperature of the fuel tank results in lower evaporative emissions.

An electric turbine style fuel pump attaches to the primary fuel tank module inside the fuel tank. The fuel pump supplies high pressure fuel through the fuel filter, past the fuel pressure regulator, and through the fuel feed pipe to the fuel injection system. The fuel pressure regulator has a T-joint that diverts the needed fuel to the fuel rail with the unused fuel dropping back into the reservoir of the primary fuel tank module. The primary fuel tank module contains a reverse flow check valve. The check valve and the fuel pressure regulator maintain fuel pressure in the fuel feed pipe and the fuel rail in order to prevent long cranking times.

The primary fuel tank module also contains a primary jet pump and a secondary jet pump. Fuel pump flow loss, caused by vapor expulsion in the pump inlet chamber, is diverted to the primary jet pump and the secondary jet pump through a restrictive orifice located on the pump cover. The primary jet pump fills the reservoir of the primary fuel tank module. The secondary jet pump creates a venturi action which causes the fuel to be drawn from the secondary side of the fuel tank, through the fuel transfer pipe, to the primary side of the fuel tank.

Reference Information

Description and Operation

Fuel System Description

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions
    •  Scan Tool Output Controls

Special Tools Required

    • CH-48027-100 Digital Pressure Gage
    • J 43936 Fuel Pressure Adapter Cap
    • J 43937 Fuel Pressure Adapter Lines
    • SA9127E-7 Fuel Pressure/Flow Adapter

Circuit/System Verification

Important: 

   • Inspect the fuel system for damage or external leaks before proceeding.
   • Verify that adequate fuel is in the fuel tank before proceeding.
   • The fuel pump relay may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
   • Before proceeding with this test review the User Manual CH 48027-5 for Safety Information and Instructions.

  1. Ignition ON, engine OFF, command the fuel pump relay ON with a scan tool. You should hear the fuel pump turn ON and OFF.
  2. If the fuel pump does not operate, refer to Fuel Pump Electrical Circuit Diagnosis .
  3. Ignition OFF, all accessories OFF, install a CH-48027-100 . Refer to Fuel Pressure Gage Installation and Removal .
  4. Ignition ON, engine OFF, command the fuel pump relay ON with a scan tool. Verify the fuel pressure is between 345-414 kPa (50-60 psi) and does not decrease more than 100 kPa (14.5 psi) in 5 minutes.

Circuit/System Testing

    Important: 

       • The fuel pump relay may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
       • DO NOT start the engine.

  1. Ignition ON, engine OFF, command the fuel pump relay ON with a scan tool and observe the fuel pressure gage while the fuel pump is operating. Verify the fuel pressure is between 345-414 kPa (50-60 psi).
  2. If the fuel pressure is greater than the specified range, replace the primary fuel tank module.
    If the fuel pressure is less than the specified range, test, inspect, and repair the items listed below. If all items test normal, replace the primary fuel tank module.
    • Restricted fuel feed pipe
    • Restricted or plugged strainer
    • Inspect the harness connectors and the ground circuits of the fuel pump for poor connections.
  3. Verify that the fuel pressure does not decrease more than 100 kPa (14.5 psi) in 5 minutes.
  4. If the fuel pressure decreases more than the specified value, perform the following procedure:
    2.1. Ignition OFF, relieve the fuel pressure. Refer to Fuel Pressure Relief .
    2.2. Disconnect the chassis fuel feed hose from the engine compartment fuel pipe. Refer to Metal Collar Quick Connect Fitting Service .
    2.3. Connect the chassis fuel feed hose to the inlet side of SA9127E-7 using the J 43937 .
    2.4. Connect the engine compartment fuel pipe to the ON/OFF valve side of the SA9127E-7 using the J 43937 .
    2.5. Cap the pressure test port on the SA9127E-7 with the J 43936 .
    2.6. Open the valve on the SA9127E-7 .
    2.7. Ignition ON, command the fuel pump relay ON with a scan tool and bleed the air from the CH-48027-100 .
    2.8. Command the fuel pump relay ON for a minimum of 10 seconds with a scan tool.
    2.9. Close the valve on the SA9127E-7 .
    2.10. Monitor the fuel pressure for 5 minutes.
    If the fuel pressure decreases more than 55 kPa (8 psi) within the specified time, locate and replace the leaking fuel injector(s).
    If the fuel pressure does not decrease more than 55 kPa (8 psi) within the specified time, replace the primary fuel tank module.
  5. Relieve the fuel pressure to 69 kPa (10 psi). Verify that the fuel pressure does not decrease more than 14 kPa (2 psi) in 5 minutes.
  6. If the fuel pressure decreases more than the specified value, replace the primary fuel tank module.
  7. Operate the vehicle within the conditions of the customer's concern while monitoring the fuel pressure with the CH-48027-100 . The fuel pressure should not drop off during acceleration, cruise, or hard cornering.
  8. If the fuel pressure drops off, test, inspect, and repair the items listed below. If all items test normal, replace the primary fuel tank module.
    • Restricted fuel feed pipe
    • Restricted or plugged strainer
    • Inspect the harness connectors and the ground circuits of the fuel pump for poor connections.
  9. If the fuel system tests normal, refer to Symptoms - Engine Controls .

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Hose/Pipes Replacement - Chassis
    •  Fuel Injector and Fuel Rail Replacement
    •  Secondary Fuel Tank Module Replacement