The accelerator pedal position (APP) sensors 1 and 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:
• | A 5-volt reference circuit |
• | A low reference circuit |
• | A signal circuit |
The APP sensor provides the engine control module (ECM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at rest position is near the low reference and increases as the pedal is actuated. The APP sensor 2 signal voltage at rest position is also near the low reference and increases as the pedal is actuated. When the ECM detects that the APP sensor 2 signal voltage is outside the predicted range, DTC P2125 will set.
This diagnostic procedure supports the following DTC:
DTC P2125 Accelerator Pedal Position (APP) Sensor 2 Circuit
• | The ignition is ON. |
• | The ignition voltage is greater than 5.25 volts. |
• | DTC P0641 is not set. |
• | DTC P2125 runs continuously when the above conditions are met. |
The APP sensor 2 voltage is less than 0.13 volts, or more than 4.87 volts for more than 0.5 second.
• | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
• | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
• | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
• | A message center or an indicator displays Reduced Engine Power. |
• | Under certain conditions the control module commands the engine OFF. |
• | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
• | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
• | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
• | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No |
---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the voltage is less than the first value or greater than the second value? | 0.13 V 4.87 V | Go to Step 5 | Go to Step 3 |
3 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections |
4 |
Does the scan tool indicate that the voltage is more than the specified value? | 4.8 V | Go to Step 5 | Go to Step 12 |
5 | Probe the APP sensor 2 signal circuit with a test lamp connected to ground. Does the test lamp illuminate? | -- | Go to Step 12 | Go to Step 6 |
6 | Observe the APP sensor 2 parameter with the test lamp still connected to the APP sensor 2 signal circuit. Does the scan tool indicate that the voltage is less than the specified value? | 0.13 V | Go to Step 7 | Go to Step 11 |
7 | Measure the voltage of the APP sensor 2 5-volt reference circuit with a DMM. Does the DMM indicate that the voltage is more than the specified value? | 4.8 V | Go to Step 8 | Go to Step 10 |
8 |
Is the resistance less than the specified value? | 5 ohms | Go to Step 9 | Go to Step 14 |
9 | Test the APP sensor low reference circuit for a short to ground. Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 18 |
10 | Does the DMM indicate that the voltage is less than the specified value on the APP sensor 2 5-volt reference circuit? | 5 V | Go to Step 14 | Go to Step 16 |
11 | Test the APP sensor 2 signal circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 13 |
12 | Test the APP sensor 2 signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
13 | Test the APP sensor 2 signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
14 | Test the APP sensor 2 low reference circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
15 | Test the APP sensor 2 5-volt reference circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 16 |
16 | Test the APP sensor 2 5-volt reference circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 20 |
17 | Test the APP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 22 | -- |
18 | Inspect for poor connections at the accelerator pedal harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 19 |
19 | Replace the accelerator pedal assembly. Refer to Accelerator Pedal with Position Sensor Assembly Replacement . Did you complete the replacement? | -- | Go to Step 22 | -- |
20 | Inspect for poor connections at the ECM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 22 | Go to Step 21 |
21 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 22 | -- |
22 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 23 |
23 |
Important: Be aware that repairing one individual condition may correct more than one DTC. Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK |