Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3715 00: Front Wiper Relay Drive CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
WPR HI Relay B+ | 1, 2 | 1, 2 | -- | -- |
Windshield Wiper Switch Signal | B3922 00 | 1 | 1 | -- |
Windshield Wiper Switch High Signal | 4 | 2 | 2 | -- |
Windshield Wiper Motor Park Switch Signal | 3 | 3 | -- | -- |
WPR Relay Control | B3715 02 | 1 | 4 | -- |
WPR HI Relay Control | 4 | 2 | B3875 00 | -- |
Windshield Wiper Motor High Speed Control | 2 | 2 | 4 | -- |
Windshield Wiper Motor Low Speed Control | 1 | 1 | 4 | -- |
Windshield Wiper Switch Low Reference | -- | 1, 2 | 1, 2 | -- |
Windshield Wiper Motor Ground | -- | 1, 2, 3 | -- | -- |
WPR Relay Ground | -- | 1 | -- | -- |
1. Delay or Low Speed Wipers Inoperative 2. High Speed Wipers Inoperative 3. Wipers Do Not Park 4. Wipers Always ON | ||||
Circuit/System Description
The body control module (BCM) monitors the control circuit of the wiper relay. The voltage level should be low while the wiper relay is de-energized and near system voltage when the relay is energized. After the BCM receives a low, intermittent, or mist signal from the wiper/washer switch, it responds by applying battery voltage through the wiper relay control circuit to the coil side of the relay, energizing the WIPER relay.
Conditions for Running the DTC
This DTC can set only when the output is actively being requested by the BCM.
Conditions for Setting the DTC
If the BCM detects a short to ground in the wiper relay control circuit.
Action Taken When the DTC Sets
The BCM will not activate the output.
Conditions for Clearing the DTC
| • | The current DTC will become history when the request for the output is removed or when the condition for setting the fault is corrected. |
| • | The history DTC will clear after 50 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Wiper/Washer System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, wiper switch in LOW position. Verify the windshield wipers are cycling at the low speed.
Circuit/System Testing
- Ignition OFF, disconnect the WPR relay.
- Connect a test lamp between the control circuit terminal 86 and ground.
- Ignition ON, command the low speed wipers ON and OFF using the wiper switch. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the WPR relay.
| ⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test for a short to ground or an open/high resistance on the control circuit. If the circuit tests normal, replace the BCM. |
Component Testing
Relay Test
- Ignition OFF, disconnect the WPR relay.
- Test for 60-200 ohms between terminals 85 and 86.
- Test for infinite resistance between the following terminals:
- Test for less than 2 ohms between terminals 30 and 87A.
- Install a 10A fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
| ⇒ | If the resistance is not within the specified range, replace the relay. |
| • | 30 and 86 |
| • | 30 and 87 |
| • | 30 and 85 |
| • | 85 and 87 |
| ⇒ | If not the specified value, replace the relay. |
| ⇒ | If greater than the specified range, replace the relay. |
| ⇒ | If greater than the specified range, replace the relay. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, setup, and programming
