GM Service Manual Online
For 1990-2009 cars only

Inspections

Action

DEFINITION: Steady pulsation or jerking that follows engine speed, usually more pronounced as engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or low speed.

Preliminary

    • Refer to Important Preliminary Inspections Before Beginning in Symptoms - Engine Controls .
    • Search for bulletins.
    • Verify that the engine control module (ECM) grounds are clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics .
    • Remove the air filter element and inspect for dirt and for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.

Fuel Systems

    • Test for incorrect fuel pressure. Refer to Fuel System Diagnosis .
    • Inspect for a restricted fuel filter. Refer to Fuel System Diagnosis .
    • Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Inspect for the following conditions that may cause the engine to run rich:

Notice: Refer to Heated Oxygen and Oxygen Sensor Notice in the Preface section.

       - Water intrusion in the HO2S connector
       - Purging of a saturated EVAP canister
       - Incorrect fuel pressure--Refer to Fuel System Diagnosis .
       - A leaking fuel pressure regulator--Refer to Fuel System Diagnosis .
       - Leaking fuel injectors--Refer to Fuel System Diagnosis .
       - Proper operation of the MAP sensor--Refer to DTC P0105 .
       - Vacuum hoses that are split, kinked, or improperly connected
       - An air intake duct that is collapsed or restricted
       - An air filter that is dirty or restricted--Refer to Air Cleaner Element Replacement .
    • Inspect for the following conditions that may cause the engine to run lean:

Notice: Refer to Heated Oxygen and Oxygen Sensor Notice in the Preface section.

       - Water intrusion in the HO2S connector
       - An exhaust leak between the HO2S and the engine--Refer to Exhaust Leakage in Engine Exhaust.
       - Vacuum leaks
       - Incorrect fuel pressure--Refer to Fuel System Diagnosis .
       - Restricted fuel injectors--Refer to Fuel Injector Balance Test with Special Tool and Fuel Injector Balance Test with Tech 2 .
       - Proper operation of the MAP sensor--Refer to DTC P0105 .
       - Fuel contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
       - Vacuum hoses that are split, kinked, or improperly connected

Sensor/System

    • Verify that the engine coolant temperature (ECT) sensor is not shifted in value. Refer to Temperature Versus Resistance .
    • Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Refer to Scan Tool Data List .
    • Inspect for throttle body tampering, excessive deposits, or damage. Refer to Throttle Body Cleaning Procedure .
    • Inspect for a vacuum leak.
    • Inspect the crankcase ventilation system for proper operation. Refer to Crankcase Ventilation System Inspection/Diagnosis in Engine Mechanical.

Ignition System

    • In order to properly inspect the spark plugs or to correct a condition, refer to the following procedures:
       -  Spark Plug Inspection
       -  Spark Plug Replacement
    • Inspect for proper secondary ignition voltage output with J 26792 (SA9199Z) Spark Tester.
    • An improper spark plug gap will cause a driveability condition. Gap the spark plugs using a wire gauge gap tool.
    • If the spark plugs are found to be fouled, determine the cause before replacing the spark plugs.
    • Inspect for damaged or misaligned spark plug boots.
    • Inspect the electronic ignition (EI ) module for a proper ground connection.
    • Monitor the Misfire Current Counters while driving the vehicle in the conditions that the symptom occurred. If a misfiring cylinder can be located, use the DTC P0300 table for diagnosis. Refer to DTC P0300 .

Engine Mechanical

    • Inspect engine mechanical for the following:
       - Compression
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Valve timing
       - Worn rocker arms
       - Broken valve springs
       - Excessive oil in combustion chamber or leaking valve seals.
       - For more information, refer to one or more of the following procedures in Engine Mechanical:
    • For incorrect, worn, or damaged basic engine parts, inspect the following:
       - The camshaft--Refer to Camshaft Cleaning and Inspection in Engine Mechanical.
       - The cylinder heads--Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical.
       - The pistons, etc.--Refer to Piston, Connecting Rod, and Bearing Cleaning and Inspection in Engine Mechanical.
    • Refer to Symptoms - Engine Mechanical in Engine Mechanical for diagnosis procedures.

Additional Inspections

    • Inspect the exhaust system for possible restrictions. Inspect for the following:
       - Inspect the exhaust system for damaged or collapsed pipes.
       - Inspect the mufflers for heat distress or possible internal failure.
       - Inspect for possible plugged catalytic converters. Refer to Restricted Exhaust in Engine Exhaust.
    • Electromagnetic interference (EMI) can cause an engine misfire condition. A sudden increase in indicated RPM parameter with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components near ignition control circuits if a condition exists.
    • Inspect the intake manifold and the exhaust manifold passages for casting flash.