Description
The purpose of the inspection/maintenance (I/M) complete system set procedure is to satisfy the enable criteria necessary to execute all of the I/M readiness diagnostics, and complete the trips for those particular diagnostics. When all diagnostic tests are completed, the I/M System Status indicators are set to YES. Perform this test when more than one or all of the I/M System Status indicators are set to NO.
Conditions for Running
Cold Start
| • | The barometric pressure is more than 74 kPa. |
| • | The engine coolant temperature (ECT) is between 4-55°C (39-131°F). |
| • | The intake air temperature (IAT) is between 6-65°C (39-149°F). |
| • | The difference between the IAT and the ECT is 9°C (16°F) or less. |
| • | The battery voltage is between 11-18 volts. |
| • | The fuel level is between 10-90 percent. |
Diagnostic Aids
Rough road conditions may prevent some of the tests from running. Extreme high or low ambient temperatures may prevent tests such as HO2S Heater and EVAP System from initiating. If a step is interrupted before completion, perform the remaining portion of the set procedures. Any portion of the set procedure that requires the engine at operating temperature may be repeated. This allows most of the diagnostics to run and the remaining tests can be performed using the individual System Set Procedures.
The scan tool can be used to monitor each of the I/M System Status indicators during the I/M complete system set procedure. When all of the indicators for a test step have updated to YES, testing can move on to the next step even if the remaining portion of the test is not complete. For example, step 3 is designed to run the EVAP, AIR, and HO2S tests. The procedure instructs the technician to operate the vehicle in the enable conditions for 6 minutes. If all 3 tests have updated to YES within 4 minutes, it is not necessary to continue with the enable conditions and testing can advance to the next step.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step is to run the HO2S Heater Tests and initiate the EVAP System Test.
-
This step is to run the EVAP, AIR and the Oxygen Sensor Tests. The EVAP Test begins once the engine coolant reaches a calibrated temperature. The AIR Test, if equipped, begins shortly after Closed Loop and the indicated speed is achieved. The Oxygen Sensor Tests begin once the engine is at operating temperature, in Closed Loop Fuel Control, and a calibrated amount of time has elapsed.
-
This step is to run the Catalyst Tests. This test runs during the idle period immediately following a cruise period that meets a minimum calibrated RPM and time period.
-
The I/M System Status only reports on whether or not a diagnostic has run, not what the outcome of the test was. If any emission related DTC sets after the tests are complete, the DTC will require diagnosis.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Inspection/Maintenance (I/M) System Check? | -- | Go to Step 2 | |||||||
Is the action complete? | 2 minutes | Go to Step 3 | -- | |||||||
|
Caution: Refer to Road Test Caution in the Preface section. In order for the next group of tests to run, the vehicle must operate in the following conditions:
Is the action complete? | -- | Go to Step 4 | -- | |||||||
|
Caution: Refer to Road Test Caution in the Preface section. In order for the next group of tests to run, the vehicle must operate in the following conditions:
Is the action complete? | -- | Go to Step 5 | -- | |||||||
5 | Observe the I/M System Status display with a scan tool. Did all of the I/M System Status indicators update to YES? | -- | Go to Step 6 | Go to the I/M System Set Procedure for the indicated systems that have not passed | ||||||
Observe the Emission Related DTC portion of the I/M System Status display with a scan tool. Does the scan tool indicate any Emission Related DTCs set? | -- | System OK |
