Inside Rearview Mirror with the Automatic Day-Night Feature System Components
The inside rearview mirror with the automatic day-night feature system consist
of the following components:
| • | Ambient air temperature sensor |
Power and Ground of the Inside Rearview Mirror
| • | With the ignition ON, ignition voltage is supplied to the mirror from
the RADIO (IGN) 10A fuse in the I/P fuse block. |
| • | Ground for the mirror is provided by G401. |
Inside Rearview Mirror with the Automatic Day-Night Feature System Operation
The inside rearview mirror uses 2 photocell sensors. One sensor is
the headlight sensor, located on the rear side of the mirror. The headlight sensor
is used to determine light conditions present at the mirror face. The other sensor
is the ambient light sensor, located on the front of the mirror or windshield side.
The ambient light sensor is used to determine light conditions present at the mirror.
With automatic day-night feature enabled, the mirror uses ambient light sensor
to determine the exterior light condition. With a low light condition detected,
and a high light condition from behind at the headlight sensor, the inside rearview
mirror will automatically darken the face of the mirror.
In the daytime, the mirror is in a normal state because of the high light
condition that is indicated by the ambient light sensor. With the gear selector
lever in the REVERSE position, backup lamp supply voltage is supplied as an input
to the inside rearview mirror. In night time conditions only, the mirror monitors
this input to disable the automatic day-night feature which allows the face to
gradually change to a normal state. This allows the driver to see objects in the
mirror clearly when backing up.
Compass
The mirror uses two magnetic field sensors for compass direction. One sensor
is for north and south, the other is for east and west. The mirror supplies a signal
and low reference to each sensor. As the vehicle travels with or against the earths
magnetic pull, there will be a change in voltage on one or both sensors. As a result
of the change in voltage, the mirror changes the heading on the compass display.
Temperature Display
The inside rearview mirror monitors the ambient air temperature sensor. As the
outside air temperature gets warmer, the ambient air temperature sensor will lower
resistance. The inside rearview mirror monitors this change and will show this as
a warmer temperature on the display. Temperatures exceeding 62°C (143°F)
will be out of the mirrors temperature range and SC will be shown on the temperature
display. In colder outside air temperatures, the ambient air temperature sensor
will raise in resistance. The inside rearview mirror will show a colder temperature
on the display. Temperatures lower than -40°C (-40°F) will be out of the
mirrors temperature range which OC will be shown on the temperature display. In
cold temperatures such as 3°C (37°F) or below, the temperature display
will show ICE when the ignition is first turned on. The display will toggle between
ICE and the actual outside temperature until the temperature update process is complete.
Temperature Display Update Process
The inside rearview mirror has a temperature program that takes in account
the fact that the radiator will heat the ambient air temperature sensor if
the radiator is warm and the vehicle is not moving. If the vehicle has been
off for more than 2 hours, the mirror temperature program assumes that the
radiator has cooled and that the temperature supplied by the ambient air temperature
sensor is accurate. Because of this, if the vehicle has been off for more than
2 hours, the mirror displays the temperature as reported by the ambient
air temperature sensor. When the ambient air temperature sensor reports a new
temperature to the mirror, one of the following cases will apply:
| • | Ignition is off for more than 2 hours, then is turned on for more
than 3 minutes. The outside temperature is greater than the last temperature
recorded by the mirror for 2 minutes. The mirror will increase the last
temperature reading by one degree every 2 minutes for 8 consecutive
times. If the outside temperature is not matched after the 8th update, the mirror
will then display the current outside temperature. |
| • | Ignition is off for more than 2 hours, then is turned on for less
than 3 minutes. The mirror will update the temperature display every 2 seconds. |
| • | Ignition is off for more than 2 hours, then is turned on for more
than 3 minutes. The outside temperature is less than the last temperature
recorded by the mirror. The mirror will then display the current outside
temperature. |
| • | Ignition has been off for less than 2 hours. The outside temperature
is greater than the last temperature recorded by the mirror, but the ignition
is cycled from on to off within 2 minutes. The mirror will display the
old temperature. |
| • | Ignition has been off for less than 2 hours. The outside temperature
is less than the last temperature recorded by the mirror. The mirror will
then display the current outside temperature. |
Switches of the Inside Rearview Mirror with the Automatic Day-Night Feature,
Compass/Temperature Display with OnStar®
The inside rearview mirror has four switches that perform the following
functions:
| • | The on/off switch located at the left side of the mirror performs
the following functions: |
| - | To enable or disable the automatic day-night feature of the mirror.
With the ignition in the ON position, depress and hold the on/off switch for
approximately 6 seconds to enable the automatic day-night feature of the
mirror. A green indicator will illuminate on the mirror when
the automatic day-night feature is enabled. To disable the
automatic day-night feature of the mirror, depress and hold the
on/off switch for approximately 6 seconds. |
| - | To turn the compass/temperature display on and off. With the ignition
in the ON position, depress the on/off switch to turn the compass/temperature
display to Fahrenheit (°F). Depress the on/off switch again to turn
the compass/temperature from Fahrenheit (°F) to Celsius (°C). Depress
the on/off switch again to turn off the display. The on/off switch is
also used to place the compass into a calibration or zone mode.
For more information, refer to
Compass Calibration and Magnetic Variance
. |
| • | The three switches on the right side of the mirror are for OnStar®
operation. For more information, refer to
OnStar Description and Operation
in Cellular Communications. |
