Circuit Description
Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensor to reach operating temperature. Voltage is provided to the heater by the ignition 1 voltage circuit through a fuse. With the engine running, ground is provided to the heater by the HO2S heater low control circuit, though a low side driver within the engine control module (ECM). The ECM monitors the current flow through the heater for diagnosis.
If the ECM detects that the HO2S heater current is outside a specified range, DTC P0135 sets for HO2S 1 or DTC P0141 sets for HO2S 2.
Conditions for Running the DTC
| • | DTCs P0105, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0125, P0128, P0201 P0202, P0203, P0204, P0300-P0304, P0336, P0440, P0442, P0446, P0452, P0453, P0506, P0507, P0601, P0602, P0604, P0606, P1120, P1220, P1221, P1271, P1275, P1280, P1441, P1512, P1514, P1515, P1516, P1621, P1635, P1639, P1680, P1681 are not set. |
| • | The Ignition 1 Signal parameter is between 10-17 volts. |
| • | The ECT Sensor parameter is more than 70°C (158°F). |
| • | The Fuel Level Sensor parameter is more than 10 percent. |
| • | The Engine Run Time parameter is more than 60 seconds. |
Conditions for Setting the DTC
| • | The ECM detects that the affected HO2S heater current is less than 0.217 amps or more than 1.56 amps. |
| • | The above condition is met for 200 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||
2 |
Is the HO2S heater current parameter within the specified range? | 0.217-1.56 A | Go to Step 3 | Go to Step 4 | ||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions | ||||
4 | Inspect the EMISS fuse. Is the EMISS fuse open? | -- | Go to Step 5 | Go to Step 6 | ||||
5 | Test the ignition 1 voltage circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 8 | ||||
6 |
Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 17 | ||||
7 |
Does the test lamp turn ON and OFF with each command? | -- | Go to Step 9 | Go to Step 10 | ||||
8 |
Important: Perform the following test on all HO2S' which are supplied voltage by the suspect circuit. Test the ignition 1 voltage circuit on the sensor side of the HO2S connector for a short to ground. Refer to Circuit Testing in Wiring Systems. Is any sensor shorted to ground? | -- | Go to Step 18 | Go to Intermittent Conditions | ||||
9 | Measure the resistance of the following circuits with a DMM:
Refer to Circuit Testing in Wiring Systems. Is the resistance of either circuit more than the specified value? | 3 ohms | Go to Step 16 | Go to Step 14 | ||||
10 | Does the test lamp remain illuminated with each command? | -- | Go to Step 11 | Go to Step 12 | ||||
11 | Test the HO2S heater low control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||
12 | Test the HO2S heater low control circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 13 | ||||
13 | Test the HO2S heater low control circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||
14 | Test for an intermittent and for a poor connection at the HO2S. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 18 | ||||
15 | Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||
16 | Repair the circuit with high resistance. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 20 | -- | ||||
17 | Repair the open in the ignition 1 voltage circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 20 | -- | ||||
18 | Replace the affected HO2S. Refer to Heated Oxygen Sensor 1 Replacement or Heated Oxygen Sensor 2 Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
19 | Replace the ECM. Refer to Engine Control Module Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
20 | Were you sent to this diagnostic from DTC P0134? | -- | Go to Step 18 in DTC P0134 | Go to Step 21 | ||||
21 | Were you sent to this diagnostic from DTC P0140? | -- | Go to Step 18 in DTC P0140 | Go to Step 22 | ||||
22 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 23 | ||||
23 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |||||
