GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2005 🢒 VUE - FWD 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC P0602

Circuit Description

A normal function of the transmission control module (TCM) is to perform an internal test that verifies the security of the diagnostic and control calibration programming. The programming must contain security codes that enable a software lock to engage. The software lock is designed to prevent unauthorized changes to the diagnostics or control calibrations. The software lock utility is processed independently from the diagnostic and control calibration software and contains application specific data. The software lock data is entered into the TCM during the final assembly of the vehicle.

When the security codes from the diagnostic and shift calibration software fail to engage the software lock, the TCM sets DTC P0602. DTC P0602 is a type A DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0602 Transmission Control Module (TCM) Not Programmed

Conditions for Running The DTC
    • No TCM DTC P0601.
    • The engine is running.

Conditions for Setting The DTC

The TCM detects an unlocked calibration memory range.

Action Taken When the DTC Sets
    • The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL).
    • The TCM inhibits TCC engagement.
    • The TCM commands a line pressure increase for all operating conditions.
    • The TCM freezes main line pressure transmission adaptive functions.
    • The TCM freezes torque converter clutch (TCC) transmission adaptive functions.
    • The ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as Freeze Frame and Failure Records.
    • The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records.
    • The TCM stores DTC P0602 in TCM history.

Conditions for Clearing the MIL/DTC
    • The ECM turns OFF the MIL after the third consecutive drive trip in which the TCM does not send a MIL illumination request.
    • A scan tool can clear the MIL/DTC.
    • The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring.
    • The TCM cancels the default actions when the ignition switch is OFF long enough in order to power down the TCM.

Diagnostic Aids

DTC P0602 may set as a result of TCM reprogramming.

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step eliminates the TCM software as a possible cause of the DTC. If the DTC continues to set after reprogramming, the fault is in the TCM hardware.

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.

    3. Important: 

       • Before clearing the DTC, use the scan tool in order to record the Failure Records. Using the Clear DTC Info function erases the Failure Records from the ECM and the TCM.
       • Using the Clear DTC Info function erases stored DTCs in both the ECM and TCM.

  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Turn OFF the ignition for at least 30 seconds.
  6. Turn ON the ignition.

Did DTC P0602 reset?

--

Go to Step 3

Go to Diagnostic Aids

3

Perform the Transmission Control Module Reprogramming Procedure. Refer to Transmission Control Module Reprogramming .

Did the DTC P0602 reset?

--

Go to Step 4

Go to Step 5

4

Replace the TCM.

Refer to Control Module References in Computer/Integrating Systems for replacement, set-up and programming.

Is the replacement complete?

--

Go to Step 5

--

5

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Turn OFF the ignition for at least 30 seconds.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
  5. Select Specific DTC.
  6. Enter DTC P0602.

Has the test run and passed?

--

Go to Step 6

Go to Step 2

6

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK