Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0201: Injector 1 Control CircuitDTC P0202: Injector 2 Control Circuit
DTC P0203: Injector 3 Control Circuit
DTC P0204: Injector 4 Control Circuit
DTC P0205: Injector 5 Control Circuit
DTC P0206: Injector 6 Control Circuit
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Fuel Injector 1-3-5 Ignition Voltage | P0201¹, P0203¹, P0205¹, P0300¹ | P0201, P0203, P0205 | -- | -- |
Fuel Injector 2-4-6 Ignition Voltage | P0202¹, P0204¹, P0206¹, P0300¹ | P0202, P0204, P0206, P0300 | -- | -- |
Fuel Injector 1 Control | P0201, P0300 | P0201, P0300 | P0201, P0300 | -- |
Fuel Injector 2 Control | P0202, P0300 | P0202, P0300 | P0202, P0300 | -- |
Fuel Injector 3 Control | P0203, P0300 | P0203, P0300 | P0203, P0300 | -- |
Fuel Injector 4 Control | P0204, P0300 | P0204, P0300 | P0204, P0300 | -- |
Fuel Injector 5 Control | P0205, P0300 | P0205, P0300 | P0205, P0300 | -- |
Fuel Injector 6 Control | P0206, P0300 | P0206, P0300 | P0206, P0300 | -- |
¹Open fuse | ||||
Circuit/System Description
The control module enables the appropriate fuel injector pulse for each cylinder. Ignition voltage is supplied to each bank of fuel injectors through a separate fuse. The control module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of each driver. If the control module detects an incorrect voltage for the commanded state of the driver, a fuel injector control circuit DTC sets.
Conditions for Running the DTC
| • | The engine is running. |
| • | The ignition voltage is more than 11 volts for 5 seconds. |
| • | DTC P0201-P0206 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
| • | The control module detects an incorrect voltage on the fuel injector control circuit. |
| • | The above condition is met for 1 second. |
Action Taken When the DTC Sets
DTCs P0201-P0206 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0201-P0206 are Type B DTCs.
Diagnostic Aids
Performing the Fuel Injector Diagnosis may help isolate an intermittent condition. Refer to Fuel Injector Diagnosis.
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Key ON, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, or P0206 should not be set.
Circuit/System Testing
- Ignition OFF, disconnect the X110 fuel injector multi-way connector.
- Ignition ON, verify that a test lamp illuminates between the ignition circuit terminals A and E engine control module (ECM) harness side and ground.
- Ignition OFF, connect a test lamp between the ignition circuit terminal A and the control circuit ECM harness side, of the appropriate injector listed below:
- Engine cranking, the test lamp should flash for each injector.
- Ignition OFF, measure for 10-15 ohms on the engine harness side of X110 between the ignition circuit terminal A or E and the control circuit of the appropriate injector listed below:
| ⇒ | If the test lamp does not illuminate, test the ignition circuits for a short to ground, or an open/high resistance. If the circuits test normal and the ignition circuit fuse is open, test or replace the fuel injector. |
| • | Injector 1 terminal B |
| • | Injector 2 terminal F |
| • | Injector 3 terminal C |
| • | Injector 4 terminal G |
| • | Injector 5 terminal D |
| • | Injector 6 terminal H |
| ⇒ | If the test lamp is always ON, test the appropriate control circuit for a short to ground. If the circuit tests normal, replace the ECM. |
| ⇒ | If the test lamp is always OFF, test the appropriate control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM. |
| • | Injector 1 terminal B |
| • | Injector 2 terminal F |
| • | Injector 3 terminal C |
| • | Injector 4 terminal G |
| • | Injector 5 terminal D |
| • | Injector 6 terminal H |
| ⇒ | If the resistance is not within the specified range, test for a short to ground or an open/high resistance between X110 and the appropriate fuel injector harness connector. If the circuits test normal, test or replace the affected fuel injector. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming |
