Diagnostic Instructions
DTC Descriptors
DTC P0340: Intake Camshaft Position (CMP) Sensor Circuit Bank 1
DTC P0345: Intake Camshaft Position (CMP) Sensor Circuit Bank 2
DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit Bank 1
DTC P0390: Exhaust Camshaft Position (CMP) Sensor Circuit Bank 2
Diagnostic Fault Information
Circuit
| Short to Ground
| Open/High Resistance
| Short to Voltage
| Signal Performance
|
5-Volt Reference Circuit
| P0641, P0452, P0107, P0532, P0522
| P0340, P0345, P0365, P0390
| P0641
| --
|
CMP Sensor Signal Circuit
| P0340, P0345, P0365, P0390
| P0340, P0345, P0365, P0390
| P0340, P0345, P0365, P0390
| P0341, P0346, P0366, P0391
|
Low Reference Circuit
| --
| P0340, P0345, P0365, P0390
| P0340, P0345, P0365, P0390
| --
|
Circuit/System Description
The 4X camshaft position (CMP) sensor circuits consist of an engine control module (ECM) supplied 5-volt reference circuit, low reference circuit, and an output signal circuit. The CMP sensor is an internally magnetic biased digital output integrated
circuit sensing device. The sensor detects magnetic flux changes of the teeth and slots of a 4-tooth reluctor wheel attached to the camshaft. As each reluctor wheel tooth rotates past the CMP sensor, the resulting change in the magnetic field is used by the
sensor electronics to produce a digital output pulse. The sensor returns a digital ON/OFF DC voltage pulse of varying frequency, with 4 varying width output pulses per camshaft revolution that represent an image of the camshaft reluctor wheel. The frequency
of the CMP sensor output depends on the velocity of the camshaft. The ECM decodes the narrow and wide tooth pattern to identify camshaft position. This information is then used to determine the optimum ignition and injection points of the engine. The ECM also
uses CMP sensor output information to determine the camshaft relative position to the crankshaft, to control camshaft phasing, and for limp-home operation.
Conditions for Running the DTC
• | DTC P0335, P0336, P0641 or P0651 is not set. |
• | The engine is cranking or running. |
• | The DTCs run continuously when the above conditions are met. |
Conditions for Setting the DTC
Important: The ECM detects engine movement by sensing the airflow through the mass air flow (MAF) sensor is more than 3 g/s, or by sensing crankshaft position (CKP) sensor pulses.
• | The ECM detects that the starter is commanded ON and the engine has been cranking for more than 4 seconds without a CMP sensor pulse. |
• | The ECM detects that the engine has started, but did not received a CMP sensor pulse during the first engine revolution. |
• | The ECM detects that the engine is running, but does not receive a CMP sensor pulse for 800 of 1,000 engine cycles. |
Action Taken When the DTC Sets
• | DTCs P0340, P0345, P0365, and P0390 are Type B DTCs. |
• | The CMP actuator is commanded to the Home or Parked position. |
• | The ignition system defaults to a failed CMP sensor limp home mode. |
Conditions for Clearing the MIL/DTC
• | DTCs P0340, P0345, P0365, and P0390 are Type B DTCs. |
• | With a DTC set, the engine may crank for an extended period of time at start-up. |
Diagnostic Aids
With a DTC set, the engine may crank for an extended period of time at start-up
Reference Information
Schematic Reference
Engine Controls Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Electronic Ignition (EI) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Start the engine. Using the Live Plot function on the scan tool, select the CMP parameter. Change the minimum spec to 400 RPM and the maximum spec to 4,000 RPM. Select the CKP sensor parameter. Change the minimum spec to 600 RPM
and the maximum spec to 3,300 RPM.
- Observe the scan tool.
- Quickly accelerate and release the accelerator pedal several times. Do not exceed 3,200 RPM. The graphed lines on the Live Plot display should track together across the screen.
⇒ | If the vehicle passes the Circuit/System Verification Test, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data
List. |
Circuit/System Testing
- Ignition OFF, disconnect the affected CMP sensor connector.
- Test for less than 1 ohm between the low reference circuit terminal 1 and ground.
⇒ | If greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and ground.
⇒ | If less than the specified range, test the 5-volt reference circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the ECM. |
⇒ | If greater than the specified range, test
the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 2 and ground.
⇒ | If less than the specified range, test the affected signal circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the ECM. |
⇒ | If greater than the specified range, test the affected
signal circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
- Ignition ON, using a jumper wire connected to ground, momentarily touch the CMP sensor signal circuit terminal 2 repeatedly. The applicable CMP active counter parameter should increment.
⇒ | If the CMP active counter does not increment, replace the ECM. |
⇒ | If the circuits test normal, replace the CMP sensor. |
Component Test
Important: You must perform the Circuit/System Testing before proceeding with Component Testing.
- Inspect the CMP sensor for looseness and correct installation. Remove the CMP sensor from the engine and inspect the sensor and the O-ring for damage.
⇒ | If the sensor is loose, incorrectly installed, or damaged, repair or replace the CMP sensor. |
- Connect the CMP sensor connector to the CMP sensor. Turn ON the ignition, with the engine OFF.
- Ignition ON and engine OFF. Observe the applicable CMP Active Counter parameter on the scan tool. Pass a steel object by the tip of the sensor repeatedly. The CMP Active Counter parameter should increment.
⇒ | If the parameter does not increment, replace the CMP sensor. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.