Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B1370 01: Device Ignition 1 Circuit Short to BatteryDTC B1370 06: Device Ignition 1 Circuit Short to Ground or Open
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
Ignition 1 Circuit | B1370 06 | -- | B1370 06 | B1370 01 | B1370 06 |
Circuit/System Description
The inflatable restraint sensing and diagnostic module (SDM) monitors the ignition 1 signal from the ignition switch. The SDM also compares the ignition 1 input to the power mode message communicated over the vehicle bus. When the vehicle ignition switch is placed in the RUN or CRANK position, voltage is applied to the SDM ignition 1 input terminal. If a fault is detected in the SDM ignition 1 circuit, then DTC B1370 will set.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
The following conditions exist for at least 10 seconds.
B1370 01
The SDM detects a short to battery in the ignition 1 voltage circuit when the switch is in the OFF position.
B1370 06
| • | The SDM detects a short to ground or an open in the ignition 1 voltage circuit when the ignition switch is in RUN or CRANK. |
| • | The SDM sees that the vehicle power mode message is Run/Crank but does not detect the Run/Crank voltage on the ignition 1 input. |
| • | There is an open circuit on the in the control side of the RUN/Crank relay. |
Action Taken When the DTC Sets
| • | The SDM commands the AIR BAG indicator ON via serial data communications. |
| • | The SDM stores DTC to memory. |
| • | The SDM determines its power mode only from the GMLAN power mode messages and discards the ignition 1 input for the remainder of the ignition cycle. |
Conditions for Clearing the DTC
| • | A current DTC clears when the malfunction is no longer present. |
| • | A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction. |
Diagnostic Aids
The SIR fuse could be open and DTC B1370 will set if the low reference circuit is shorted to voltage/battery with no sensor code set for one of the following sensors:
| • | Right or Left front end sensors |
| • | Right or Left side impact sensors |
There is a current fault on the control side of the RUN/CRANK relay.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
SIR System Description and Operation
Electrical Information Reference
Scan Tool Reference
Circuit/System Testing
Important: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected.
• SDM • SDM wiring harness
- Ignition OFF, remove the under hood SIR Display Fuse 25.
- Ignition ON, with a DMM, test for 9-16 V between the voltage supply side and ground.
- Ignition OFF, remove the SDM harness connector.
- Ignition OFF, test for less then 1 ohm of resistance between the ignition 1 voltage circuit terminal 32 and the under hood fuse block terminal 28.
- Ignition ON, with a DMM, test for less then 1 volt between the ignition 1 voltage circuit terminal 32 and the under hood fuse block terminal 28.
- If all circuits test normal, replace the SDM.
| ⇒ | If not the specified range, refer to DTC B1370 . |
| ⇒ | If greater then the specified range, test the circuit for an open/high resistance. |
| ⇒ | If greater then the specified value, test the circuit for a short to voltage. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for SDM replacement, setup, and programming |
