Diagnostic Instructions

DTC Descriptors

DTC B0015 01: LF Pretensioner Deployment Loop Short to Battery

DTC B0015 02: LF Pretensioner Deployment Loop Short to Ground

DTC B0015 04: LF Pretensioner Deployment Loop Open Circuit

DTC B0015 0D: LF Pretensioner Deployment Loop Resistance Above Threshold

DTC B0015 0E: LF Pretensioner Deployment Loop Resistance Below Threshold

DTC B0016 01: LF Roof Rail Deployment Loop Stage 1 Short to Battery

DTC B0016 02: LF Roof Rail Deployment Loop Stage 1 Short to Ground

DTC B0016 04: LF Roof Rail Deployment Loop Stage 1 Open Circuit

DTC B0016 0D: LF Roof Rail Deployment Loop Stage 1 Resistance Above Threshold

DTC B0016 0E: LF Roof Rail Deployment Loop Stage 1 Resistance Below Threshold

DTC B0019 01: Passenger Frontal Deployment Loop Stage 1 Short to Battery

DTC B0019 02: Passenger Frontal Deployment Loop Stage 1 Short to Ground

DTC B0019 04: Passenger Frontal Deployment Loop Stage 1 Open Circuit

DTC B0019 0D: Passenger Frontal Deployment Loop Stage 1 Resistance Above Threshold

DTC B0019 0E: Passenger Frontal Deployment Loop Stage 1 Resistance Below Threshold

DTC B0020 01: Passenger Frontal Deployment Loop Stage 2 Short to Battery

DTC B0020 02: Passenger Frontal Deployment Loop Stage 2 Short to Ground

DTC B0020 04: Passenger Frontal Deployment Loop Stage 2 Open Circuit

DTC B0020 0D: Passenger Frontal Deployment Loop Stage 2 Resistance Above Threshold

DTC B0020 0E: Passenger Frontal Deployment Loop Stage 2 Resistance Below Threshold

DTC B0022 01: RF Pretensioner Deployment Loop Short to Battery

DTC B0022 02: RF Pretensioner Deployment Loop Short to Ground

DTC B0022 04: RF Pretensioner Deployment Loop Open Circuit

DTC B0022 0D: RF Pretensioner Deployment Loop Resistance Above Threshold

DTC B0022 0E: RF Pretensioner Deployment Loop Resistance Below Threshold

DTC B0023 01: RF Roof Rail Deployment Loop Stage 1 Short to Battery

DTC B0023 02: RF Roof Rail Deployment Loop Stage 1 Short to Ground

DTC B0023 04: RF Roof Rail Deployment Loop Stage 1 Open Circuit

DTC B0023 0D: RF Roof Rail Deployment Loop Stage 1 Resistance Above Threshold

DTC B0023 0E: RF Roof Rail Deployment Loop Stage 1 Resistance Below Threshold

Diagnostic Fault Information

Circuit	Short to Ground	Low Resistance	High Resistance	Open	Short to Voltage
Seat Belt Pretensioner - Driver Low Control	B0015 02	B0015 0E	B0015 0D	B0015 04	B0015 01
Seat Belt Pretensioner - Driver - High Control	B0015 02	B0015 0E	B0015 0D	B0015 04	B0015 01
Roof Rail Module - Left - Low Control	B0016 02	B0016 0E	B0016 0D	B0016 04	B0016 01
Roof Rail Module - Left - High Control	B0016 02	B0016 0E	B0016 0D	B0016 04	B0016 01
IP Module - Stage 1 - Low Control	B0019 02	B0019 0E	B0019 0D	B0019 04	B0019 01
IP Module - Stage 1 - High Control	B0019 02	B0019 0E	B0019 0D	B0019 04	B0019 01
IP Module - Stage 2 - Low Control	B0020 02	B0020 0E	B0020 0D	B0020 04	B0020 01
IP Module - Stage 2 - High Control	B0020 02	B0020 0E	B0020 0D	B0020 04	B0020 01
Seat Belt Pretensioner - Passenger - Low Control	B0022 02	B0022 0E	B0022 0D	B0022 04	B0022 01
Seat Belt Pretensioner - Passenger - High Control	B0022 02	B0022 0E	B0022 0D	B0022 04	B0022 01
Roof Rail Module - Right - Low Control	B0023 02	B0023 0E	B0023 0D	B0023 04	B0023 01
Roof Rail Module - Right - High Control	B0023 02	B0023 0E	B0023 0D	B0023 04	B0023 01

Circuit/System Description

During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy an inflatable restraint module. There are 2 shorting bars used within the module connector which will short together both high and low circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0015 01, B0016 01, B0019 01, B0020 01, B0022 01, B0023 01

The inflatable restraint module high and/or low circuit is shorted to voltage for 120 milliseconds.

B0015 02, B0016 02, B0019 02, B0020 02, B0022 02, B0023 02

The inflatable restraint module high and/or low circuit is shorted to ground for 120 milliseconds.

B0015 04, B0016 04, B0019 04, B0020 04, B0022 04, B0023 04

The inflatable restraint module high and/or low circuit is open for 120 milliseconds.

B0015 0D, B0016 0D, B0019 0D, B0020 0D, B0022 0D, B0023 0D

The inflatable restraint module deployment loop resistance is greater than 3.9 ohms for 120 milliseconds.

B0015 0E, B0016 0E, B0019 0E, B0020 0E, B0022 0E, B0023 0E

The inflatable restraint module deployment loop resistance is less than 1.1 ohms for 120 milliseconds.

Action Taken When the DTC Sets

Conditions for Clearing the DTC

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

SIR System Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Special Tools

Each inflatable restraint module requires a specific adapter to connect the load tool to the SIR system.

J 38715-A Driver and Passenger SIR Load Tool

Circuit/System Testing

Important: Refer to SIR Service Precautions.

When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.

•	Pretensioner

•	Inflatable restraint module

•	SDM module

•	Inflatable restraint module wiring harness connector

•	SDM wiring harness connector

1. Ignition OFF, disconnect the harness connector at the appropriate inflatable restraint module.
2. With the appropriate adaptor, connect J 38715-A in place of the inflatable restraint module.
3. Ignition ON, with a scan tool, verify DTC is set as current.

⇒	If DTC is not set or is set as history, replace the appropriate inflatable restraint module.

4. Ignition OFF, disconnect J 38715-A and the appropriate adaptor.
5. Disconnect the harness connector at the SDM.
6. Ignition ON, test for less than 1 volt between the appropriate high control circuit and ground.

•	I/P module Stage 1 terminal 1 X1

•	I/P module Stage 2 terminal 1 X2

•	Left roof rail module terminal 2

•	Right roof rail module terminal 2

•	Left seat belt pretensioner terminal 1

•	Right seat belt pretensioner terminal 1

⇒	If not the specified range, test the circuit for a short to voltage.

7. Test for less than 1 volt between the appropriate low control circuit terminal and ground.

•	I/P module Stage 1 terminal 2 X1

•	I/P module Stage 2 terminal 2 X2

•	Left roof rail module terminal 1

•	Right roof rail module terminal 1

•	Left seat belt pretensioner terminal 2

•	Right seat belt pretensioner terminal 2

⇒	If not the specified range, test the circuit for a short to voltage.

8. Ignition OFF, test for infinite resistance between the appropriate high control circuit terminal and ground.

•	I/P module Stage 1 terminal 1 X1

•	I/P module Stage 2 terminal 1 X2

•	Left roof rail module terminal 2

•	Right roof rail module terminal 2

•	Left seat belt pretensioner terminal 1

•	Right seat belt pretensioner terminal 1

⇒	If not the specified range, test the circuit for a short to ground.

9. Test for infinite resistance between the appropriate low control circuit terminal and ground.

•	I/P module Stage 1 terminal 2 X1

•	I/P module Stage 2 terminal 2 X2

•	Left roof rail module terminal 1

•	Right roof rail module terminal 1

•	Left seat belt pretensioner terminal 2

•	Right seat belt pretensioner terminal 2

⇒	If not the specified range, test the circuit for a short to ground.

10. Test for less then 1 ohm between the following high control circuit terminals.

•	I/P module Stage 1 terminal 1 X1 and SDM terminal 10

•	I/P module Stage 2 terminal 1 X2 and SDM terminal 6

•	Left roof rail module terminal 2 and SDM terminal 13

•	Right roof rail module terminal 2 and SDM terminal 14

•	Left seat belt pretensioner terminal 1 and SDM terminal 17

•	Right seat belt pretensioner terminal 1 and SDM terminal 18

⇒	If not the specified range, test the circuit for an open/high resistance.

11. Test for less then 1 ohm between the following low control circuit terminals.

•	I/P module Stage 1 terminal 2 X1 and SDM terminal 11

•	I/P module Stage 2 terminal 2 X2 and SDM terminal 7

•	Left roof rail module terminal 1 and SDM terminal 12

•	Right roof rail module terminal 1 and SDM terminal 15

•	Left seat belt pretensioner terminal 2 and SDM terminal 16

•	Right seat belt pretensioner terminal 2 and SDM terminal 19

⇒	If not the specified range, test the circuit for an open/high resistance.

12. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.