GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 45185 Bore Gage Set


    Object Number: 1850794  Size: SH
  1. Remove the input shaft thrust bearing (540).
  2. Remove the front sun gear assembly (544).
  3. Remove the rear sun gear thrust bearing (538).

  4. Object Number: 749494  Size: SH
  5. Remove the rear sun gear thrust bearing race (537).
  6. Remove the rear internal gear (536).
  7. Remove the rear internal gear thrust bearing (535).

  8. Object Number: 1850795  Size: SH
  9. Remove the front carrier thrust bearing race (543).
  10. Remove the front carrier assembly (542).

  11. Object Number: 1826686  Size: SH
  12. Remove the rear internal gear flange retaining ring (548) from the rear internal gear (536).
  13. Remove the rear internal gear flange (547) from the rear internal gear.
  14. Remove the other rear internal gear flange retaining ring (548).

  15. Object Number: 1419809  Size: SH
  16. Clean the rear internal gear and air dry.
  17. Inspect the rear internal teeth for the following:
  18. • Chips
    • Cracks
    • Excessive wear
    • Metal debris embeded in teeth
  19. Replace the rear internal gear if any of the above conditions are found.

  20. Object Number: 1826686  Size: SH
  21. Install a rear internal gear flange retaining ring (548).
  22. Install the rear internal gear flange (547) in the rear internal gear (536).
  23. Install the other rear internal gear flange retaining ring (548).
  24. If the rear sun gear bushing is not within specifications or any of the above conditions are found, replace the rear sun gear.

  25. Object Number: 749703  Size: SH
  26. Clean the front carrier assembly (542) and air dry. Ensure to remove all solvent in the pinion gears.
  27. Inspect the front carrier assembly pinion teeth for the following conditions:
  28. • Chips
    • Cracks
    • Excessive wear
    • Metal debris embeded in teeth
  29. Inspect for missing washers on both sides of the pinion gears.
  30. Inspect the front carrier bushing for scoring or excessive wear.
  31. Using J 45185 and a micrometer measure the front carrier bushing inner diameter (A). Measure in three locations and take the average.
  32. Specification
    Front carrier bushing: 30.056-30.132 mm (1.183-1.186 in)

  33. If the front carrier bushing is not within specifications or any of the above conditions are found, replace the front carrier assembly.

  34. Object Number: 1850796  Size: SH
  35. Clean the front sun gear (544) and air dry.
  36. Inspect the front sun gear teeth for the following conditions:
  37. • Chips
    • Cracks
    • Excessive wear
    • Metal debris embeded in teeth
  38. Inspect the rear sun gear teeth for the following:
  39. • Chips
    • Cracks
    • Excessive wear
    • Metal debris embeded in teeth
  40. Inspect the front sun gear shaft for excessive wear or scoring at the front carrier assembly bushing area.
  41. Using J 45185 and a micrometer measure the bushing inner diameter (A). Measure in three locations and take the average.
  42. Specification
    Front sun gear bushing: 22.200-22.276 mm (0.874-0.877 in)

  43. If the front sun gear bushings are not within specifications or any of the above conditions are found, replace the front sun gear.

  44. Object Number: 1850797  Size: SH
  45. Inspect the bushing for scoring or excessive wear.
  46. Using J 45185 and a micrometer measure the rear sun gear bushing inner diameter (A). Measure in three locations and take the average.
  47. Specification
    Rear sun gear bushing: 22.200-22.276 mm (0.874-0.877 in)