Rear Compartment Lid Release Inoperative Hardtop/Convertable
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Body Rear End Diagnostic System Check been performed? | -- | ||
2 |
Does the scan tool indicate the switch is active when pressed? | -- | ||
3 | Inspect the F/TNKDR fuse #32 for an open. Is the fuse open? | -- | ||
4 | Test and repair circuit 2840 for a short to ground. Did you find and correct the condition? | -- | ||
5 | Test and repair the switched circuits from circuit 2840 for a short to ground. Refer to Power Distribution Schematics in Wiring Systems. Did you find and correct the condition? | -- | ||
6 | Test and repair circuit 2840 for an open or high resistance. Did you find and correct the condition? | -- | ||
7 | Test for momentary continuity across the release switch terminals while pressing the switch. Does the DMM indicate momentary continuity when the switch is pressed? | -- | ||
8 | Test and repair circuit 1576 for an open or high resistance. Did you find and correct the condition? | -- | ||
9 | Replace the rear compartment lid release switch. Refer to Rear Compartment Lid Switch Replacement . Did you complete the repair? | -- | -- | |
10 | Inspect the HTCHTRK fuse #26 for an open. Is the fuse open? | -- | ||
11 | Test and repair circuit 383 for a short to ground. Did you find and correct the condition? | -- | ||
12 |
Does the test light flash? | -- | ||
13 |
Does the test light flash? | -- | ||
14 | Reinstall the relay and fuse, replacing the inoperative HTCHTRK relay #36. Did you complete the repair? | -- | -- | |
15 | Test and repair circuit 1344 for an open or high resistance. Did you find and correct the condition? | -- | ||
16 | Test and repair circuit 383 for an open or high resistance. Did you find and correct the condition? | -- | ||
17 | Test and repair the ground circuit 150 for an open or high resistance. Did you find and correct the condition? | -- | ||
18 | Replace the rear compartment lid latch. Refer to Rear Compartment Lid Latch Replacement . Did you complete the repair? | -- | -- | |
19 | Replace the BCM. Refer to Body Control Module Replacement and Body Control Module (BCM) Programming/RPO Configuration . Did you complete the repair? | -- | -- | |
20 |
Did you correct the condition? | -- | System OK |
Rear Compartment Lid Release Inoperative Folding Top Compartment
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Body Rear End Diagnostic System Check been performed? | -- | ||
2 |
Does the scan tool indicate the switch as active when pressed? | -- | ||
3 | Inspect the TONN REL #17 fuse for an open. Is the fuse open? | -- | ||
4 |
Does the test light illuminate? | -- | ||
5 |
Does the test light illuminate? | -- | ||
6 |
With the test light connected from the folding top compartment lid latch release connector terminal A to ground, does the test light illuminate? | -- | ||
7 |
Does the DMM indicate momentary continuity to ground when the switch is pressed? | -- | ||
8 | Inspect and repair the short to ground in circuit 2168, if ok replace the folding top compartment lid latch. Refer to Folding Top Stowage Compartment Lid Latch Replacement . Is the repair complete? | -- | -- | |
9 | Replace the folding top compartment lid latch. Refer to Folding Top Stowage Compartment Lid Latch Replacement . Is the repair complete? | -- | -- | |
10 | Repair the open or high resistance in circuit 150. Is the repair complete? | -- | -- | |
11 | Repair the open or high resistance in circuit 2168. Is the repair complete? | -- | -- | |
12 | Inspect and repair the open or high resistance in circuit 2169, if ok replace the BCM. Refer to Body Control Module Replacement and Body Control Module (BCM) Programming/RPO Configuration . Is the repair complete? | -- | -- | |
13 | Replace the TONN REL micro relay #41. Is the repair complete? | -- | -- | |
14 |
Does the scan tool indicate the switch is active, with the jumper wire connected? | -- | ||
15 | Inspect and repair the open or high resistance in circuit 2166, if ok replace the BCM. Refer to Body Control Module Replacement and Body Control Module (BCM) Programming/RPO Configuration . Is the repair complete? | -- | -- | |
16 | Inspect and repair the open or high resistance in circuit 150, if ok replace the folding top compartment lid release switch. Is the repair complete? | -- | -- | |
17 |
Did you correct the condition? | -- | System OK |
