Fuel Sender Assembly Replacement Replacement

Tools Required

J 39765 , Fuel Sender Locknut Wrench

Caution: In order to Reduce the Risk of Personal Injury: Always allow for proper ventilation when working with fuel in enclosed areas.

Caution: Always wear safety goggles when working with fuel in order to protect the eyes from fuel splash.

Notice: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

Important: Always replace the fuel sender O-rings when reinstalling the fuel sender assembly.

1. Relieve the fuel system fuel pressure. Refer to the Fuel Pressure Relief Procedure .
2. Drain the fuel tank to no more than 1/4 of a tank full. Refer to Fuel Tank Replacement (Draining Fuel Tank) .



3. Remove the spare tire cover, the jack, and the spare tire.
4. Pull back the trunk liner.
5. Remove the fuel sender access panel.



6. Remove the quick-connect fittings at the fuel sender assembly. Refer to Servicing Quick Connect Fittings .
7. Remove the electrical connector at the fuel sender.
8. Remove the fuel sender retaining ring using the J 39765 Fuel Sender Spanner Wrench.

Important: When removing the modular fuel sender assembly from the fuel tank, the reservoir bucket on the fuel sender assembly is full of fuel. The modular fuel sender assembly must be tipped slightly during removal in order to avoid damage to the float. Place any remaining fuel into an approved container once the modular fuel sender assembly is removed from the fuel tank.

Important: The modular fuel sender assembly will spring-up when the locking ring is removed.

9. Pull the modular fuel sender straight up while pumping the fuel from the reservoir.
10. Clean the fuel sender assembly O-ring sealing surfaces.
11. Inspect the fuel sender assembly O-ring sealing surfaces.

1. Position the new fuel sender assembly O-ring on the fuel tank.

Important: Care should be taken not to fold over or twist the fuel pump strainer when installing the fuel sender assembly, as this will restrict fuel flow. Also, assure that the fuel pump strainer does not block full travel of float arm.

2. Install the fuel sender assembly and the fuel sender assembly retainer cam using the J 39765 Fuel Sender Spanner Wrench.
3. Install the quick-connect fittings at the fuel sender assembly. Refer to Servicing Quick Connect Fittings .
4. Install the negative battery cable.
5. Inspect for leaks.

5.1.	Turn the ignition switch to the On position for 2 seconds.

5.2.	Turn the ignition switch to the Off for 10 seconds.

5.3.	Turn the ignition switch to the On position.

5.4.	Check for fuel leaks.




6. Install the fuel sender access panel.

Tighten
Tighten the fuel sender access panel bolts to 2N·m (18 lb in).

7. Reposition the trunk liner.
8. Install the spare tire, the jack, and the spare tire cover.



9. Add fuel and install the fuel tank filler pipe cap.

Fuel Sender Assembly Replacement Serviceable Components

Caution: Provide proper ventilation when working with fuel in enclosed areas where fuel vapors can collect. The lack of adequate ventilation may result in personal injury.

Caution: Always wear safety goggles when working with fuel in order to protect the eyes from fuel splash.

Notice: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

1. Relieve the fuel system fuel pressure. Refer to the Fuel Pressure Relief Procedure .
2. Drain the fuel tank to no more than 1/4 of a tank full. Refer to Fuel Tank Replacement (Draining Fuel Tank) .




Important: The modular fuel sender support assembly will spring-up when the locking ring is moved.

3. Remove the fuel sender assembly. Refer to Fuel Sender Assembly Replacement .

1. Note the position of the fuel sender strainer for installation (1).
2. Support the reservoir with one hand and grasp the fuel sender strainer with the other hand.



3. Pull the fuel sender strainer off of the fuel sender assembly.
4. Inspect the fuel sender strainer. If the fuel sender strainer is contaminated, the fuel tank should be cleaned. Refer to Fuel System Cleaning .
5. Discard the fuel sender strainer after inspection.



6. Disassemble the electrical connectors from the sensor assembly of the fuel pump and the cover assembly.
7. Disassemble the fuel level sensor assembly.

1. Assemble the fuel level sensor assembly.
2. Assemble the electrical connectors to the fuel pump and the cover assembly.
3. Assemble the rubber pad on the bottom of the modular fuel sender.



4. Position the new fuel sender strainer on the modular fuel sender and push on the outer edge of the fuel sender strainer until the fuel sender strainer is fully seated.

1. Install the fuel sender assembly. Refer to Fuel Sender Assembly Replacement (Replacement) .



2. Install the spare tire cover, the jack, and the spare tire.
3. Install the trunk liner.
4. Install the fuel sender access panel.

Tighten
Tighten the fuel sender access panel bolts to 2N·m (18 lb in).




5. Add fuel and install the fuel tank filler pipe cap.