DTC P0507 Idle Speed High. Oldsmobile Intrigue 1999

For 1990-2009 cars only

Makes 🢒 Oldsmobile 🢒 1999 🢒 Intrigue 🢒 Engine 🢒 Engine Controls - 3.5L 🢒 DTC P0507 Idle Speed High

(IAC) Valve, Engine Oil Level Indicator Switch, Engine Oil Pressure Switch
Engine Controls Components
OBD II Symbol Description Notice
ESD Notice

Circuit Description

The PCM controls engine idle speed by adjusting the position of the Idle Air Control (IAC) motor pintle. The IAC is a bi-directional motor driven by two coils. The PCM sends pulses (steps) to the IAC to extend or retract the IAC pintle into a passage in the throttle body to decrease or increase air flow. The commanded IAC position (displayed in counts) can be monitored on the scan tool; a lower number of counts indicates less commanded airflow (pintle extended). This method allows highly accurate control of idle speed and quick response to changes in engine load. If the PCM detects a condition where too high of an idle speed is present and the PCM is unable to adjust idle speed by decreasing the IAC counts, DTC P0507 will set indicating a problem with the idle control system.

Conditions for Running the DTC

•	No Fuel injector faults, Misfire, Fuel Trim, EVAP, EGR, VSS, TP, IAT, MAP, ECT, CKP or MAF sensor DTCs set.

•	BARO is greater than 65 kPa.

•	Engine has been running for at least 3 minutes.

•	System voltage is between 9 and 18 volts.

•	Engine Coolant Temperature is greater than 70°C (158°F).

•	Vehicle Speed is less than 3 MPH.

•	Intake Air Temperature is greater than -18°C (0°F).

•	The throttle is closed.

•	Conditions stable for at least 15 seconds.

Conditions for Setting the DTC

Engine Speed is more than 175 RPM higher than Desired Idle (positive idle speed error greater than 175 RPM).

Action Taken When the DTC Sets

•	The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

•

The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

•	The PCM turns the MIL Off after three consecutive drive trips that the diagnostic runs and does not fail.

•	A last test failed (current DTC) clears when the diagnostic runs and does not fail.

•	A History DTC clears after forty consecutive warm-up cycles, if this or any other emission related diagnostic does not report any failures.

•	Use a scan tool in order to clear the MIL/DTC.

•	Interrupting the PCM battery voltage may or may not clear DTCs. This practice is not recommended. Refer to Powertrain Control Module (PCM) Description , Clearing Diagnostic Trouble Codes.

Diagnostic Aids

Notice: Use the connector test adapter kit J 35616-A for any test that requires probing the following items:

•	The PCM harness connectors

•	The electrical center fuse/relay cavities

•	The component terminals

•	The component harness connector

Using this kit will prevent damage caused by the improper probing of connector terminals.

Check for the following conditions:

•	Poor connection at PCM or IAC motor. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.

•	Damaged harness. Inspect the wiring harness for damage.

•	Vacuum leak. Check for a condition that causes a vacuum leak, such as disconnected or damaged hoses, leaks at EGR valve and EGR pipe to intake manifold, leaks at throttle body, malfunctioning or incorrectly installed PCV valve, leaks at intake manifold, etc.

•	Throttle body. Check for a sticking throttle plate. Also inspect the IAC passage for deposits or objects which will not allow the IAC pintle to fully extend.

Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to set occurs. This may assist in diagnosing the condition.

If the problem is intermittent, refer to Intermittent Conditions .

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table.

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.

Step

Action

Value(s)

Yes

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

Go to Step 2

Go to the Powertrain On Board Diagnostic (OBD) System Check

Are any other DTC(s) set?

Go to the applicable DTC table.

Go to Step 3

Start the engine.
Turn OFF all accessories (A/C, Rear defroster etc.).
Using a scan tool, command RPM up to 1500, down to 650, and then up to 1500 while monitoring Engine Speed on the scan tool.

Does Engine Speed remain within the specified value of Desired Idle Speed for each RPM command?

± 100 RPM

Refer to Diagnostic Aids.

Go to Step 4

Leave the engine running.
Disconnect the IAC.
Install the J 37027-A IAC System Monitor node light.
With the engine running, momentarily blip the throttle while observing the IAC System Monitor node lights.

Does each node light cycle red and green (never OFF)?

Go to Step 6

Go to Step 5

Check the following circuits for an open, short to voltage, or short to ground:

•	IAC A Low.

•	IAC A High.

•	IAC B Low.

•	IAC B High.

If a problem is found, repair as necessary.

Was a problem found?

Go to Step 11

Go to Step 9

Visually/physically inspect for the following conditions:

•	Vacuum leaks.

•	Throttle body tampering (throttle lever stop screw turned).

•	Throttle plate or throttle shaft for binding.

•	Accelerator and cruise control cables for being misadjusted or for binding. Refer to Accelerator Control Cable Replacement .

•	Malfunctioning, missing, or incorrectly installed PCV valve. Refer to Crankcase Ventilation System Diagnosis .

If a problem is found, repair as necessary.

Was a problem found and corrected?

Go to Step 11

Go to Step 7

Check for a poor connection at the IAC harness connector.
If a problem is found, replace terminals as necessary. Refer to Intermittents and Poor Connections Diagnosis .

Was a problem found and corrected?

Go to Step 11

Go to Step 8

Replace the IAC valve. Refer to Idle Air Control Valve Replacement .

Is the action complete?

Go to Step 11

Check for a poor connection at the PCM harness connector.
If a problem is found, replace terminals as necessary. Refer to Intermittents and Poor Connections Diagnosis .

Was a problem found and corrected?

Go to Step 11

Go to Step 10

Replace the PCM.

Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .

Is the action complete?

Go to Step 11

Start engine.
Turn OFF all accessories (A/C, Rear defroster etc.).
Using a scan tool, command RPM up to 1500, down to 650, and then up to 1500 while monitoring Engine Speed on the scan tool.

Does Engine Speed remain within the specified value of Desired Idle Speed for each RPM command?

± 100 RPM

Go to Step 12

Go to Step 2

Review Captured Info using the scan tool.

Are there any DTCs that have not been diagnosed?

Go to the applicable DTC table

System OK