Drive Belt Tensioner Replacement VIN 1
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
- Disconnect
the negative battery cable.
- Raise the vehicle. Suitably support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Remove the front lower splash shield.
- Drain the coolant. Refer to
Cooling System Draining and Filling
in Engine Cooling.
- Close the radiator drain cock.
- Install the front splash shield.
- Lower the vehicle.
- Remove the fuel injector sight shield. Refer to
Fuel Injector Sight Shield Replacement
.
- Remove the drive belt. Refer to
Drive Belt Replacement
.
- Remove the generator. Refer to
Generator Replacement
in Engine Electrical.
- Disconnect the heater hoses from the drive belt tensioner.
- Remove the drive belt
tensioner bolts.
- Remove the drive belt tensioner.
Installation Procedure
- Install the tensioner.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the drive
belt tensioner bolts.
Tighten
Tighten the drive belt tensioner bolts to 50 N·m (37 lb ft).
- Connect the heater hoses to the tensioner.
- Install the generator. Refer to
Generator Replacement
in Engine Electrical.
- Install the drive belt. Refer to
Drive Belt Replacement
.
- Install the fuel injector sight shield. Refer to
Fuel Injector Sight Shield Replacement
.
- Refill the coolant. Refer to
Cooling System Draining and Filling
in Engine Cooling.
- Connect the negative battery cable.
Drive Belt Tensioner Replacement VIN K
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
- Disconnect
the negative battery cable.
- Drain the coolant. Refer to
Cooling System Draining and Filling
in Engine Cooling.
- Remove the fuel injector sight shield. Refer to
Fuel Injector Sight Shield Replacement
.
- Remove the drive belt. Refer to
Drive Belt Replacement
.
- Remove the generator. Refer to
Generator Replacement
in Engine Electrical.
- Remove the heater hoses. Refer to
Radiator Inlet Hose Replacement
in Engine Cooling.
- Remove the drive belt
tensioner bolts.
- Remove the drive belt tensioner.
Installation Procedure
- Install the drive belt
tensioner.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the drive
belt tensioner bolts.
Tighten
Tighten the drive belt tensioner bolts to 50 N·m (37 lb ft).
- Install the heater hoses. Refer to
Radiator Inlet Hose Replacement
in Engine Cooling.
- Install the generator. Refer to
Generator Replacement
in Charging System.
- Install the drive belt. Refer to
Drive Belt Replacement
.
- Install the fuel injector sight shield. Refer to
Fuel Injector Sight Shield Replacement
.
- Refill the coolant. Refer to
Cooling System Draining and Filling
in Engine Cooling.
- Connect the negative battery cable.