GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 CTS 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Lack of Power, Sluggishness, or Sponginess

Inspections

Action

DEFINITION: The engine delivers less than expected power. Little increase in speed, or a total lack of acceleration when the accelerator pedal is pushed down part way.

Preliminary
    • Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls .
    • Search for bulletins.
    • Inspect the engine control system grounds for being clean, tight, and in the correct locations. Refer to Engine Controls Schematics . Ensure the resistance between the engine control module (ECM) housing and the battery negative cable is less than 0.5 ohms.
    • Verify that the ECM and ECM bracket fasteners are at the correct torque.
    • Remove the air filter element and inspect for restrictions. Refer to Air Cleaner Element Replacement .
    • Inspect the intake air duct and air cleaner outlet resonator for the following conditions:
       - Restrictions
       - Improperly installed hoses
       - Leaks
       - Collapsed hoses

Fuel System
    • Test for incorrect fuel system pressure. Refer to Fuel System Diagnosis .
    • Test for a restricted fuel filter. Refer to Fuel System Diagnosis .
    • Test for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Test the fuel injectors. Refer to Fuel Injector Solenoid Coil Test .
    • Test the items that cause an engine to run rich. For a rich condition, refer to DTC P2178 or P2180 and DTC P2188 or P2190 .
    • Test the items that can cause an engine to run lean. For a lean condition, refer to DTC P2177 or P2179 and DTC P2187 or P2189 .

Sensor/System

Monitor the knock sensor (KS) system for excessive spark retard activity with a scan tool. Refer to Knock Sensor (KS) System Description , DTC P0327 or P0332 , and DTC P0328 or P0333 .

Ignition System
    • Inspect for the correct installation of the ignition coil seals. Incorrect installation may allow water to enter the spark plug area. Inspect for moisture and corrosion.
    • Test for the correct ignition voltage output with a J 26792 Spark Tester. If you suspect an ignition system condition exists, refer to Electronic Ignition (EI) System Diagnosis .
    • Remove the spark plugs and inspect for the following conditions:
       - Incorrect heat range
       - Wet plugs
       - Cracks
       - Wear
       - Improper gap
       - Burned electrodes
       - Heavy deposits
       - Refer to the following procedures:
    • If the spark plugs are gas, coolant, or oil fouled, determine the cause before replacing the spark plugs. Refer to the following procedures:
       - Test the items that cause an engine to run rich. For a rich condition, refer to DTC P2178 or P2180 and DTC P2188 or P2190 .
       - For diagnosis of coolant contaminated spark plugs, refer to Loss of Coolant .
       - For diagnosis of oil fouled spark plugs, refer to Oil Consumption Diagnosis .
    • Inspect the crankshaft position (CKP) sensor for the correct resistance. The sensor resistance may be out of range after a hot soak. Measure that the resistance remains within 700-1,200 ohms at all temperatures.
    • Inspect the spark plug boots and terminals for burning or micro-arcing, corrosion, and damage to the insulation.

Engine Mechanical
    • Inspect for a condition with the camshaft actuator system. A camshaft actuator that is stuck in the full advance or retard position may cause this symptom. Refer to DTC P0011, P0014, P0021, or P0024 .
    • Inspect for the following engine mechanical conditions:
       - Excessive oil in combustion chamber or leaking valve seals
       - Incorrect cylinder compression
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Camshaft timing
       - Broken valve springs
       - Excessive carbon buildup in the combustion chambers--Clean the chambers with top engine cleaner. Follow the instructions on the can.
       - For more information, refer to the following procedures:
    • Inspect the following components for incorrect basic engine parts:
       - Camshafts
       - Cylinder heads
       - Pistons, connecting rods, or bearings
       - Refer to the following procedures:

Additional
    • Inspect the following exhaust system components:
       - The exhaust system for damage
       - The mufflers for heat distress or possible internal failure
       - The catalytic converters for restrictions
       - For more information, refer to Symptoms - Engine Exhaust .
    • Test for the correct operation of the intake manifold runner control solenoid. Refer to Intake Manifold Runner Control System Diagnosis .
    • Test the transmission torque converter clutch (TCC) for the correct operation. Refer to Torque Converter Diagnosis .
    • Test for other transmission related faults that might cause the transmission to operate in a default mode.