Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B3119 00: Keyless Entry Antenna 1 Performance - LF Door AntennaDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Keyless Entry Antenna Signal - LF Door | B3119 00 | B3119 00 | B3119 00 | -- |
Keyless Entry Antenna Low Reference - LF Door | -- | B3119 005 | -- | -- |
Keyless Entry Antenna Signal - RF Door | B3120 00 | B3120 00 | B3120 00 | -- |
Keyless Entry Antenna Low Reference - RF Door | -- | B3120 005 | -- | -- |
Keyless Entry Antenna Signal - Rear Compartment | B3121 00 | B3121 00 | B3121 005 | -- |
Keyless Entry Antenna Low Reference - Rear Compartment | -- | B3121 00 | -- | -- |
Keyless Entry Antenna Signal - Console Passive | B3123 00 | B3123 00 | B3123 00 | -- |
Keyless Entry Antenna Low Reference - Console Passive | -- | B3123 00 | -- | -- |
Keyless Entry Antenna Ignition - Console Active | B3122 00 | B3122 00 | B3122 00 | -- |
Keyless Entry Antenna Data Signal - Console Active | B3122 00 | B3122 00 | B3122 00 | -- |
Keyless Entry Antenna Clock Signal - Console Active | B3122 00 | B3122 00 | B3122 00 | -- |
Keyless Entry Antenna Low Reference - Console Active | -- | B3122 00 | -- | -- |
Circuit/System Description
The LF door handle antenna is located in the left front door handle assembly and is used to establish low frequency (LF) communications with the keyless entry transmitter. As a vehicle with locked doors is approached with a keyless entry transmitter, known as an electronic key, and the exterior door handle is activated, the keyless entry antenna broadcasts a challenge to the transmitter in an approximately 1 meter range. If the response from the transmitter via radio frequency (RF) is valid, the locked door will be passively unlocked/unlatched and allow the door to be opened.
Conditions for Running the DTC
The left front door handle is pulled
Conditions for Setting the DTC
An improper current level is seen on the keyless entry antenna - signal (4) circuit
Action Taken When the DTC Sets
No action is taken
Conditions for Clearing the DTC
| • | A current DTC will clear when the conditions for setting the DTC are no longer present |
| • | A history DTC will clear after 50 malfunction free ignition cycles |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Keyless Entry System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the LF door handle antenna.
- Ignition ON, verify a test lamp does not illuminate between the signal circuit terminal A and ground.
- Install a DMM between the signal circuit terminal A and the low reference circuit terminal B. Set the DMM to capture AC voltage using the MIN MAX function.
- Operate the LF door handle. Verify the DMM captured an AC voltage signal.
- If all circuits test normal, test or replace the LF door handle assembly.
| ⇒ | If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RCDLR. |
| ⇒ | If an AC voltage was not captured, test the signal circuit and the low reference circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the RCDLR. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for RCDLR replacement, setup, and programming |
