GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2009 🢒 DTS 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Battery Positive Cable Replacement

Removal Procedure

Note: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.

  1. Remove the surge tank. Refer to Radiator Surge Tank Replacement.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove the carpet. Refer to Front Floor Panel Carpet Replacement and Rear Floor Panel Carpet Replacement.

    4. Object Number: 2149613 Size: SH
  4. Loosen the positive battery cable NUT (2).
  5. Separate the positive battery cable (1) from the battery.
  6. Remove the positive battery cable retainer (3) from the floor pan stud (4).

    7. Object Number: 1669915 Size: SH
  7. Remove the positive battery cable nut (1) from the junction block stud.
  8. Remove the positive battery cable terminal (2) from the junction block stud.

    9. Object Number: 1669917 Size: SH
  9. Remove the positive battery cable retainer (1) from the rocker panel.
  10. Remove the positive battery cable retainers (2, 3 and 4) from the body harness channel.

    11. Object Number: 1669919 Size: SH
  11. Remove the positive battery cable clips (2, 3, and 4) from the body harness retainers.
  12. Remove the positive battery cable clip (5) from the dash mat.
  13. Reposition the dash mat flap (1).

    14. Object Number: 1664482 Size: SH
  14. From under the hood, disengage the junction block cover lock tabs.
  15. Remove the junction block cover.

    16. Object Number: 1663997 Size: SH
  16. Remove the nut (1) securing the starter solenoid cable to the bussed electrical center (BEC).
  17. Remove the starter solenoid cable from the BEC stud.

    18. Object Number: 1669922 Size: SH
  18. Remove the positive battery cable (1) from the BEC stud.

    19. Object Number: 1669921 Size: SH
  19. Remove the positive battery clips (2) from the side engine compartment.
  20. Carefully unseat the positive battery cable grommet (1) from the front of dash.
  21. From inside the vehicle, carefully remove the positive battery cable by pulling the cable through the front of dash and out of the vehicle.

Installation Procedure

    Object Number: 1669921 Size: SH
  1. From inside the vehicle, carefully lay out the positive battery cable and route the front portion through the front of dash.
  2. From under the hood, carefully seat the positive battery cable grommet (1) to the front of dash.
  3. Install the positive battery clips (2) to the side engine compartment.

    4. Object Number: 1669922 Size: SH
  4. Install the positive battery cable (1) to the BEC stud.

    5. Object Number: 1663997 Size: SH
  5. Install the starter solenoid cable to the BEC stud.

    6. Caution: Refer to Fastener Caution in the Preface section.

  6. Install the nut (1) securing the starter solenoid cable to the BEC and tighten to 15 N·m (11 lb ft).

    7. Object Number: 1664482 Size: SH
  7. Install the junction block cover.

    8. Object Number: 1669919 Size: SH
  8. From inside the vehicle, position the dash mat flap (1) into place.
  9. Install the positive battery cable clip (5) to the dash mat.
  10. Install the positive battery cable clips (2, 3, and 4) to the body harness retainers.

    11. Object Number: 1669917 Size: SH
  11. Install the positive battery cable retainers (2, 3 and 4) to the body harness channel.
  12. Install the positive battery cable retainer (1) to the rocker panel.

    13. Object Number: 1669915 Size: SH
  13. Install the positive battery cable terminal (2) to the junction block stud.
  14. Install the positive battery cable nut (1) to the junction block stud and tighten to 15 N·m (11 lb ft).

    15. Object Number: 2149613 Size: SH
  15. Install the positive battery cable retainer (3) to the floor pan stud (4).
  16. Position the positive battery cable (1) to the battery.
  17. Tighten the positive battery cable nut (2) and tighten to 15 N·m (11 lb ft).
  18. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  19. Install the carpet. Refer to Front Floor Panel Carpet Replacement and Rear Floor Panel Carpet Replacement.
  20. Install the surge tank. Refer to Radiator Surge Tank Replacement.