GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 44212 Camshaft Holding Tool

Removal Procedure

  1. Remove the right secondary camshaft drive chain tensioner. Refer to Secondary Camshaft Drive Chain Tensioner Replacement - Right Side .
  2. Remove the right camshaft cover. Refer to Camshaft Cover Replacement - Right Side .

  3. Object Number: 517164  Size: SH
  4. Ensure both camshaft sprocket drive pins are at the top of their rotation.
  5. Caution: Refer to Camshaft Holding Tool Caution in the Preface section.


    Object Number: 650538  Size: SH
  6. Install the J 44212 over the camshafts.

  7. Object Number: 749349  Size: SH
  8. Remove the mechanics wire (1) supporting the right secondary camshaft drive chain shoe (3).
  9. Remove the engine front cover bolt (2) from the front of the engine.
  10. Notice: Refer to Torque Reaction Against Timing Drive Chain Notice in the Preface section.


    Object Number: 749351  Size: SH
  11. Use an open end wrench on the hex cast into the camshaft in order to prevent the camshaft from rotating when removing the camshaft sprocket bolt.

  12. Object Number: 210266  Size: SH
  13. Remove the right intake camshaft sprocket bolt.
  14. Slide the right intake camshaft sprocket off of the camshaft and remove the right secondary drive chain from the camshaft sprocket teeth.

  15. Object Number: 748194  Size: SH
  16. Remove the right secondary camshaft drive chain guide access plug (2) located in the cylinder head. Ensure the O-ring seal remains attached to the access plug.

  17. Object Number: 685331  Size: SH
  18. Remove the upper right secondary camshaft drive chain guide bolt.

  19. Object Number: 685347  Size: SH
  20. Remove the lower right secondary camshaft drive chain guide bolt.

  21. Object Number: 685348  Size: SH
  22. Remove the right secondary camshaft drive chain guide.
  23. Clean and inspect the camshaft timing drive components. Refer to Camshaft Timing Drive Components Cleaning and Inspection .

Installation Procedure


    Object Number: 685348  Size: SH
  1. Position the right secondary camshaft drive chain guide in through the top of the cylinder head.

  2. Object Number: 685347  Size: SH
  3. Loosely install the lower right secondary camshaft drive chain guide bolt.

  4. Object Number: 685331  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  5. Install the upper right secondary camshaft drive chain guide bolt.
  6. Tighten
    Tighten the secondary camshaft drive chain guide bolts to 25 N·m (18 lb ft).


    Object Number: 748194  Size: SH
  7. Install the right secondary camshaft drive chain guide access plug (2) located in the cylinder head. Ensure the O-ring seal is attached to the access plug.
  8. Tighten
    Tighten the secondary camshaft drive chain guide access plug to 4.5 N·m (40 lb in).


    Object Number: 517164  Size: SH
  9. Install the right intake camshaft sprocket into the right secondary camshaft drive chain.
  10. Install the right intake camshaft sprocket onto the camshaft. The camshaft sprocket notch marked RI (right intake) engages the intake camshaft pin.
  11. Notice: Refer to Torque Reaction Against Timing Drive Chain Notice in the Preface section.


    Object Number: 749351  Size: SH
  12. Use an open end wrench on the hex cast into the camshaft in order to prevent the camshaft from rotating when tightening the camshaft sprocket bolt.

  13. Object Number: 210266  Size: SH
  14. Install the right intake camshaft sprocket bolt.
  15. Tighten
    Tighten the camshaft sprocket bolt to 120 N·m (89 lb ft).

  16. Install the right secondary camshaft drive chain tensioner. Refer to Secondary Camshaft Drive Chain Tensioner Replacement - Right Side .

  17. Object Number: 650538  Size: SH
  18. Remove the J 44212 from the camshafts.
  19. Install the right camshaft cover. Refer to Camshaft Cover Replacement - Right Side .